
Printed PS lidding arrives with the artwork off-centre after forming, because sheet growth in the heater moves the print relative to the trimmed edge.
What the failure looks like on the line
PS blister packs and trays are stiff and economical, and their failure mode is usually a crack or a stressed hinge rather than a slow distortion.
The printed motif on a PS lid sits a few millimetres off the trimmed edge, and the error grows across the sheet width. Colour bars no longer line up with the seal band.
Printed sheet expands as it reaches forming temperature, and the growth is rarely uniform across the web. If the artwork is not compensated for that expansion, the formed and trimmed part cuts the print at a different position than the flat sheet layout assumed.
Most of these complaints arrive after the parts have been accepted, which is a sign that the acceptance test measured the wrong thing. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. Sheet growth allowance is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.
The process window that decides it
Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.
| 可変 | Typical window | What fails outside it |
|---|---|---|
| Sheet growth allowance | 1-3 % | Uncompensated growth shifts print at the trim |
| Heater zone balance | +/- 5 C | Uneven heating skews growth across the web |
| Print-to-trim tolerance | +/- 0.5 mm | Larger offsets are visible on shelf |
| Sheet moisture | 0.05-0.15 % | Wet sheet grows unevenly in the heater |
Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.
Sheet growth allowance is typically held at 1-3 %. Uncompensated growth shifts print at the trim Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.
Heater zone balance is typically held at +/- 5 C. Uneven heating skews growth across the web When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.
Print-to-trim tolerance is typically held at +/- 0.5 mm. Larger offsets are visible on shelf A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.
Sheet moisture is typically held at 0.05-0.15 %. Wet sheet grows unevenly in the heater Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.
Reading the response curve

The left panel shows registration yield (%) as sheet growth variation (%) increases: the response falls from 95 to 10 on the illustrative 0–100 scale. The dashed line at 60 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.
Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.
Where the causes actually sit
The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.
| 原因 | Illustrative share | First check |
|---|---|---|
| No growth compensation | 33% | Measure print-to-edge offset at the left, centre and right of the web. |
| Uneven heater zones | 25% | Compare the flat-sheet layout with the formed part registration. |
| Sheet moisture | 18% | Log heater zone temperatures across the sheet width. |
| Wrong artwork version | 14% | Check sheet moisture for the printed lot. |
| Reel wander | 10% | Confirm the artwork version is the frozen, approved one. |
Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.
No growth compensation accounts for roughly 33% of the illustrative split. Measure print-to-edge offset at the left, centre and right of the web. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Uneven heater zones accounts for roughly 25% of the illustrative split. Compare the flat-sheet layout with the formed part registration. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Sheet moisture accounts for roughly 18% of the illustrative split. Log heater zone temperatures across the sheet width. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Checks before sign-off
The order matters because each step removes a class of explanation before the next one is opened.
- Measure print-to-edge offset at the left, centre and right of the web.
- Compare the flat-sheet layout with the formed part registration.
- Log heater zone temperatures across the sheet width.
- Check sheet moisture for the printed lot.
- Confirm the artwork version is the frozen, approved one.
Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.
Writing it into the specification and the evidence pack
Print-to-trim offset shall stay within the agreed tolerance at defined positions across the web, measured on formed parts.
Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.
At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.
| Evidence item | What it must show |
|---|---|
| Approved drawing and revision | The exact geometry and tolerances the decision applies to |
| Material and colour identification | Grade, supplier, colour reference and any declared recycled content |
| Process window and change log | The agreed settings and any deviation since approval |
| Inspection record and retained samples | Method, conditions, results and a physical reference from the same lot |
Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.
The values quoted here are illustrative engineering guidance, not a measured survey. Agree the test method, the sample size and the acceptance rule before comparing numbers across suppliers.
Questions buyers ask
Is this a material problem or a process problem?
Printed sheet expands as it reaches forming temperature, and the growth is rarely uniform across the web. If the artwork is not compensated for that expansion, the formed and trimmed part cuts the print at a different position than the flat sheet layout assumed. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.
Can sheet growth allowance be traded against cycle time?
Only within the window stated in Table 1, and only with a recorded trial. Uncompensated growth shifts print at the trim A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.
What should be recorded at incoming inspection?
Keep the measurement, the method, the sample identity and the conditions together. Measure print-to-edge offset at the left, centre and right of the web. A result without its conditions cannot be compared with a later batch.
Does a change of PS require re-approval?
Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For thin-wall forming work the drawing alone is not enough; the process route is part of what was approved.
How many samples are enough for a first-article decision?
There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.
What belongs in the evidence pack?
The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.
Seeing this on a current thin-wall forming job?
Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.











