
A batch that meets density on average can still fail because the cell-size distribution, not the mass, sets the compression behaviour.
What the failure looks like on the line
Silicone foam is specified by density and compression behaviour, and both are easy to quote but hard to hold across a thick section.
Foam sheets read within the density band but feel uneven in hand and compress differently across a single pad.
Blowing-agent decomposition and crosslinking must overlap: gas has to be generated while the network is still soft enough to expand but strong enough to hold cells. If either rate shifts, cells coarsen or coalesce, so density alone no longer predicts stiffness or recovery.
Most of these complaints arrive after the parts have been accepted, which is a sign that the acceptance test measured the wrong thing. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. Blowing agent level is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.
The process window that decides it
Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.
| Variable | Typical window | What fails outside it |
|---|---|---|
| Blowing agent level | 1-4 phr | Outside the window cells coarsen or the foam collapses |
| Mould temperature | 120-170 C | A low ramp lets gas escape before the network sets |
| Cure rate versus gas rate | matched within 10% | A mismatch produces open, irregular cells |
| Mould venting area | 0.5-2% of face | Poor venting traps gas and raises local density |
Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.
Blowing agent level is typically held at 1-4 phr. Outside the window cells coarsen or the foam collapses Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.
Mould temperature is typically held at 120-170 C. A low ramp lets gas escape before the network sets When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.
Cure rate versus gas rate is typically held at matched within 10%. A mismatch produces open, irregular cells A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.
Mould venting area is typically held at 0.5-2% of face. Poor venting traps gas and raises local density Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.
Reading the response curve

The left panel shows relative foam density (%) as blowing agent level (phr) increases: the response falls from 96 to 28 on the illustrative 0–100 scale. The dashed line at 50 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.
Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.
Where the causes actually sit
The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.
| Cause | Illustrative share | First check |
|---|---|---|
| Blowing agent dosing drift | 30% | Section a pad and photograph the cell structure at fixed magnification. |
| Cure versus gas rate mismatch | 26% | Measure density at several points, not only the batch mean. |
| Low mould temperature ramp | 18% | Compare cell-size distribution against an approved reference sample. |
| Poor mould venting | 14% | Log blowing-agent lot and mould temperature together for each run. |
| Compound dispersion variation | 12% | Check compression force at a fixed deflection across the pad. |
Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.
Blowing agent dosing drift accounts for roughly 30% of the illustrative split. Section a pad and photograph the cell structure at fixed magnification. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Cure versus gas rate mismatch accounts for roughly 26% of the illustrative split. Measure density at several points, not only the batch mean. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Low mould temperature ramp accounts for roughly 18% of the illustrative split. Compare cell-size distribution against an approved reference sample. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Checks before sign-off
The order matters because each step removes a class of explanation before the next one is opened.
- Section a pad and photograph the cell structure at fixed magnification.
- Measure density at several points, not only the batch mean.
- Compare cell-size distribution against an approved reference sample.
- Log blowing-agent lot and mould temperature together for each run.
- Check compression force at a fixed deflection across the pad.
Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.
Writing it into the specification and the evidence pack
Specify a cell-size distribution and a within-pad density spread alongside the mean density, judged against an approved reference sample.
Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.
At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.
| Evidence item | What it must show |
|---|---|
| Approved drawing and revision | The exact geometry and tolerances the decision applies to |
| Material and colour identification | Grade, supplier, colour reference and any declared recycled content |
| Process window and change log | The agreed settings and any deviation since approval |
| Inspection record and retained samples | Method, conditions, results and a physical reference from the same lot |
Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.
All ranges in this article are illustrative engineering guidance rather than measured data. Treat them as a starting agenda for a process trial, not as a certificate for a batch that has not been run.
Questions buyers ask
Is this a material problem or a process problem?
Blowing-agent decomposition and crosslinking must overlap: gas has to be generated while the network is still soft enough to expand but strong enough to hold cells. If either rate shifts, cells coarsen or coalesce, so density alone no longer predicts stiffness or recovery. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.
Can blowing agent level be traded against cycle time?
Only within the window stated in Table 1, and only with a recorded trial. Outside the window cells coarsen or the foam collapses A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.
What should be recorded at incoming inspection?
Keep the measurement, the method, the sample identity and the conditions together. Section a pad and photograph the cell structure at fixed magnification. A result without its conditions cannot be compared with a later batch.
Does a change of foam require re-approval?
Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For silicone rubber work the drawing alone is not enough; the process route is part of what was approved.
How many samples are enough for a first-article decision?
There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.
What belongs in the evidence pack?
The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.
Seeing this on a current silicone rubber job?
Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.
Continue reading
- Silicone Sponge: Closed Cell, Open Cell and the Density That Decides
- Silicone Compound Formulation: Base, Filler, Additive and Cure
- Silicone Filler Types: What Reinforces, What Extends, What Ruins
- Microcellular Foam Injection Molding: Weight Out, Sink Gone, Strength Down
- Two-Roll Mill Mixing: Adding Filler, Curative and Heat History