Medical and Food-Contact Silicone: When the First Article Passes Gauging but Not the File

Ev / Blog

Medical and Food-Contact Silicone: When the First Article Passes Gauging but Not the File
Silicone rubber: a production part is the only useful reference for a discussion about process drift.

A dimensionally correct first article still needs its supporting documents requested from the supplier and checked for scope of coverage before approval.

What the failure looks like on the line

Parts for regulated applications are approved on documents as much as on dimensions; ask the supplier for documentation covering the actual construction and check its scope against your own market.

The first-article parts measure within tolerance, but the accompanying file does not clearly state which compound, cavity and process window the results cover.

A first article is evidence of one run under one set of conditions. Without a stated link between the measured parts, the compound lot and the declared scope, the approval cannot be extended to later batches; the gap is documentation scope, not part geometry.

Buyers and suppliers usually agree on the drawing and disagree on the conditions under which the drawing was checked. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. First-article sample size is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.

The process window that decides it

Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.

Değişken Typical window What fails outside it
First-article sample size 3-5 parts per cavity Fewer parts hide cavity-to-cavity spread
Measurement points per agreed drawing Undefined points make results non-comparable
Conditioning before gauging 16-24 h Unconditioned silicone parts drift in dimension
Documented scope coverage 100% of declared use Any uncovered condition invalidates the approval

Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.

First-article sample size is typically held at 3-5 parts per cavity. Fewer parts hide cavity-to-cavity spread Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.

Measurement points is typically held at per agreed drawing. Undefined points make results non-comparable When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.

Conditioning before gauging is typically held at 16-24 h. Unconditioned silicone parts drift in dimension A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.

Documented scope coverage is typically held at 100% of declared use. Any uncovered condition invalidates the approval Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.

Reading the response curve

Medical and Food-Contact Silicone: When the First Article Passes Gauging but Not the File: Approval scope confirmed (%) against Incoming checks completed
Figure 1. Left: Approval scope confirmed (%) against Incoming checks completed. Right: how audited failures of this type typically split by cause. All plotted values are illustrative engineering guidance, not a measured survey.

The left panel shows approval scope confirmed (%) as incoming checks completed increases: the response rises from 15 to 97 on the illustrative 0–100 scale. The dashed line at 90 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.

Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.

Where the causes actually sit

The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.

Neden Illustrative share First check
Scope not stated in file 30% Request the supplier's documentation and verify its scope of coverage against the intended use.
Part-to-lot link missing 24% Tie each measured part to a cavity, compound lot and process window.
Drawing revision mismatch 18% Confirm the drawing revision used for the first-article report.
Measurement method not agreed 16% Condition parts before gauging and record the interval.
Conditioning interval omitted 12% Record which conditions the approval does and does not cover.

Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.

Scope not stated in file accounts for roughly 30% of the illustrative split. Request the supplier's documentation and verify its scope of coverage against the intended use. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Part-to-lot link missing accounts for roughly 24% of the illustrative split. Tie each measured part to a cavity, compound lot and process window. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Drawing revision mismatch accounts for roughly 18% of the illustrative split. Confirm the drawing revision used for the first-article report. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Checks before sign-off

Run the same sequence on a retained good sample and on the disputed batch so the comparison means something.

  1. Request the supplier's documentation and verify its scope of coverage against the intended use.
  2. Tie each measured part to a cavity, compound lot and process window.
  3. Confirm the drawing revision used for the first-article report.
  4. Condition parts before gauging and record the interval.
  5. Record which conditions the approval does and does not cover.

Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.

Writing it into the specification and the evidence pack

Grant first-article approval only for the compound, cavity and conditions explicitly covered by the supplier's documentation, and request the supplier's documentation and verify its scope of coverage before extending it.

Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.

At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.

Evidence item What it must show
Approved drawing and revision The exact geometry and tolerances the decision applies to
Material and colour identification Grade, supplier, colour reference and any declared recycled content
Process window and change log The agreed settings and any deviation since approval
Inspection record and retained samples Method, conditions, results and a physical reference from the same lot

Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.

All ranges in this article are illustrative engineering guidance rather than measured data. Treat them as a starting agenda for a process trial, not as a certificate for a batch that has not been run.

Questions buyers ask

Is this a material problem or a process problem?

A first article is evidence of one run under one set of conditions. Without a stated link between the measured parts, the compound lot and the declared scope, the approval cannot be extended to later batches; the gap is documentation scope, not part geometry. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.

Can first-article sample size be traded against cycle time?

Only within the window stated in Table 1, and only with a recorded trial. Fewer parts hide cavity-to-cavity spread A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.

What should be recorded at incoming inspection?

Keep the measurement, the method, the sample identity and the conditions together. Request the supplier's documentation and verify its scope of coverage against the intended use. A result without its conditions cannot be compared with a later batch.

Does a change of medical food require re-approval?

Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For silicone rubber work the drawing alone is not enough; the process route is part of what was approved.

How many samples are enough for a first-article decision?

There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.

What belongs in the evidence pack?

The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.

Seeing this on a current silicone rubber job?

Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.

Talk to our silicone rubber team

Hi there! I'm John, dad and hero to awesome kid. By day, I'm a plastics manufacturing vet — injection molding, extrusion and vacuum forming — who went from factory floors to technical management. Here to share what I've learned—let's grow together!
tr_TRTR

Hızlı Teklif İsteyin

Çizimleri ve ayrıntılı gereksinimleri şu yolla gönderin

Emial: [email protected]

Veya Aşağıdaki İletişim Formunu Doldurun: