Vacuum Hole Witness Marks on Display Shells: When the Cosmetic Face Reads the Tool

Vacuum Hole Witness Marks on Display Shells: When the Cosmetic Face Reads the Tool
Thick-gauge forming: a production part is the only useful reference for a discussion about process drift.

Small dimples on the visible face of a formed display shell usually trace to vacuum hole size and placement; set a cosmetic rule before the tool is cut.

What the failure looks like on the line

Display shells are judged under retail lighting from a metre away, where surface waviness reads more strongly than measured thickness.

A regular pattern of shallow dimples appears on the show face of the shell, matching the tool's vacuum hole layout, and becomes visible after painting.

Where the softened sheet is pulled into a vacuum hole it forms a small local depression that freezes in as the part cools. Larger holes, high vacuum differential and a thin or very hot skin all deepen that depression until it prints through the finished surface.

Buyers and suppliers usually agree on the drawing and disagree on the conditions under which the drawing was checked. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. Vacuum hole diameter is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.

The process window that decides it

Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.

Variable Typical window What fails outside it
Vacuum hole diameter 0.5-1.0 mm on cosmetic faces Larger holes leave visible witness marks on the show face
Vacuum level Typically 0.7-0.9 bar differential Higher differential pulls the skin deeper into each hole
Sheet skin temperature Lower half of the 150-180 C forming window A very hot skin conforms to the hole more readily
Hole pitch on show face At least 50 mm from the primary viewing zone Dense patterns over the viewing face make marks unavoidable

Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.

Vacuum hole diameter is typically held at 0.5-1.0 mm on cosmetic faces. Larger holes leave visible witness marks on the show face Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.

Vacuum level is typically held at Typically 0.7-0.9 bar differential. Higher differential pulls the skin deeper into each hole When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.

Sheet skin temperature is typically held at Lower half of the 150-180 C forming window. A very hot skin conforms to the hole more readily A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.

Hole pitch on show face is typically held at At least 50 mm from the primary viewing zone. Dense patterns over the viewing face make marks unavoidable Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.

Reading the response curve

Vacuum Hole Witness Marks on Display Shells: When the Cosmetic Face Reads the Tool: Visible witness-mark incidence (%) against Vacuum hole diameter (mm)
Figure 1. Left: Visible witness-mark incidence (%) against Vacuum hole diameter (mm). Right: how audited failures of this type typically split by cause. All plotted values are illustrative engineering guidance, not a measured survey.

The left panel shows visible witness-mark incidence (%) as vacuum hole diameter (mm) increases: the response rises from 5 to 88 on the illustrative 0–100 scale. The dashed line at 25 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.

Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.

Where the causes actually sit

The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.

Cause Illustrative share First check
Hole diameter too large 34% Review the vacuum hole layout against the drawing's cosmetic zones before tool cutting.
Vacuum differential too high 23% Measure hole diameter on the tool with a pin gauge set.
Sheet skin too hot 18% Inspect the first-off show face under raking light before any coating.
Holes on primary viewing face 15% Compare the mark pattern against the agreed cosmetic limit sample.
Wall too thin at hole 10% Record vacuum level and sheet temperature for the approved cycle.

Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.

Hole diameter too large accounts for roughly 34% of the illustrative split. Review the vacuum hole layout against the drawing's cosmetic zones before tool cutting. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Vacuum differential too high accounts for roughly 23% of the illustrative split. Measure hole diameter on the tool with a pin gauge set. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Sheet skin too hot accounts for roughly 18% of the illustrative split. Inspect the first-off show face under raking light before any coating. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Checks before sign-off

Run the same sequence on a retained good sample and on the disputed batch so the comparison means something.

  1. Review the vacuum hole layout against the drawing's cosmetic zones before tool cutting.
  2. Measure hole diameter on the tool with a pin gauge set.
  3. Inspect the first-off show face under raking light before any coating.
  4. Compare the mark pattern against the agreed cosmetic limit sample.
  5. Record vacuum level and sheet temperature for the approved cycle.

Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.

Writing it into the specification and the evidence pack

Vacuum hole witness marks on the designated cosmetic face shall not exceed the agreed limit sample when assessed under the specified lighting, with hole diameter and vacuum level recorded for the approved cycle.

Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.

At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.

Evidence item What it must show
Approved drawing and revision The exact geometry and tolerances the decision applies to
Material and colour identification Grade, supplier, colour reference and any declared recycled content
Process window and change log The agreed settings and any deviation since approval
Inspection record and retained samples Method, conditions, results and a physical reference from the same lot

Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.

All ranges in this article are illustrative engineering guidance rather than measured data. Treat them as a starting agenda for a process trial, not as a certificate for a batch that has not been run.

Questions buyers ask

Is this a material problem or a process problem?

Where the softened sheet is pulled into a vacuum hole it forms a small local depression that freezes in as the part cools. Larger holes, high vacuum differential and a thin or very hot skin all deepen that depression until it prints through the finished surface. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.

Can vacuum hole diameter be traded against cycle time?

Only within the window stated in Table 1, and only with a recorded trial. Larger holes leave visible witness marks on the show face A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.

What should be recorded at incoming inspection?

Keep the measurement, the method, the sample identity and the conditions together. Review the vacuum hole layout against the drawing's cosmetic zones before tool cutting. A result without its conditions cannot be compared with a later batch.

Does a change of display shell require re-approval?

Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For thick-gauge forming work the drawing alone is not enough; the process route is part of what was approved.

How many samples are enough for a first-article decision?

There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.

What belongs in the evidence pack?

The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.

Seeing this on a current thick-gauge forming job?

Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.

Talk to our thick-gauge forming team

Hi there! I'm John, dad and hero to awesome kid. By day, I'm a plastics manufacturing vet — injection molding, extrusion and vacuum forming — who went from factory floors to technical management. Here to share what I've learned—let's grow together!
en_USEN

Ask For A Quick Quote

Send drawings and detailed requirements via

Emial: [email protected]

Or Fill Out The Contact Form Below: