
A part that tears on ejection is often a release-and-cure balance problem, not simply a lack of release agent.
What the failure looks like on the line
Liquid silicone rubber parts are produced at high cavitation, so one under-cured cavity can pass an average-based check and still fail in the field.
LSR parts resist ejection, tear at thin ribs, or leave a film on the cavity; the fault worsens at the lowest mould temperature in the range.
Low-viscosity LSR wets the tool face closely and, being soft at demould, has little green strength. If the surface cure is marginal or the tool texture and draft are unfavourable, adhesion to steel exceeds the part's tear strength and ejection damages it.
The useful question is not whether the part conforms, but which condition was never written into the specification. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. Mould temperature is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.
The process window that decides it
Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.
| Variable | Typical window | What fails outside it |
|---|---|---|
| Mould temperature | 170-200 C | Low temperature leaves a weak, tacky surface skin |
| Draft angle | 1-3 deg | Little draft raises ejection force sharply |
| Release-agent coverage | uniform thin film | Heavy build-up transfers to the part surface |
| Ejection force | monitored per shot | A rising trend signals sticking before parts tear |
Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.
Mould temperature is typically held at 170-200 C. Low temperature leaves a weak, tacky surface skin Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.
Draft angle is typically held at 1-3 deg. Little draft raises ejection force sharply When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.
Release-agent coverage is typically held at uniform thin film. Heavy build-up transfers to the part surface A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.
Ejection force is typically held at monitored per shot. A rising trend signals sticking before parts tear Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.
Reading the response curve

The left panel shows parts released intact (%) as release-agent coverage passes increases: the response rises from 40 to 97 on the illustrative 0–100 scale. The dashed line at 90 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.
Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.
Where the causes actually sit
The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.
| Cause | Illustrative share | First check |
|---|---|---|
| Low mould temperature | 30% | Trend ejection force shot by shot rather than reacting to torn parts. |
| Insufficient draft | 22% | Compare sticking at the low and high ends of the temperature window. |
| Release build-up or miss | 20% | Inspect cavity texture and draft on the affected ribs. |
| Cavity texture too rough | 16% | Check release-agent dilution and application interval. |
| Low green tear strength | 12% | Confirm surface cure hardness before raising ejection speed. |
Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.
Low mould temperature accounts for roughly 30% of the illustrative split. Trend ejection force shot by shot rather than reacting to torn parts. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Insufficient draft accounts for roughly 22% of the illustrative split. Compare sticking at the low and high ends of the temperature window. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Release build-up or miss accounts for roughly 20% of the illustrative split. Inspect cavity texture and draft on the affected ribs. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Checks before sign-off
Work through these in order; measuring a later variable before an earlier one hides the cause rather than finding it.
- Trend ejection force shot by shot rather than reacting to torn parts.
- Compare sticking at the low and high ends of the temperature window.
- Inspect cavity texture and draft on the affected ribs.
- Check release-agent dilution and application interval.
- Confirm surface cure hardness before raising ejection speed.
Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.
Writing it into the specification and the evidence pack
Set an ejection-force trend limit and a minimum surface hardness at demould, and require release-agent type and interval to be recorded in the process sheet.
Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.
At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.
| Evidence item | What it must show |
|---|---|
| Approved drawing and revision | The exact geometry and tolerances the decision applies to |
| Material and colour identification | Grade, supplier, colour reference and any declared recycled content |
| Process window and change log | The agreed settings and any deviation since approval |
| Inspection record and retained samples | Method, conditions, results and a physical reference from the same lot |
Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.
None of the figures above should be read as a measured survey. They are engineering guidance for framing a joint trial; confirm them on your own tool, grade and geometry before they become contract terms.
Questions buyers ask
Is this a material problem or a process problem?
Low-viscosity LSR wets the tool face closely and, being soft at demould, has little green strength. If the surface cure is marginal or the tool texture and draft are unfavourable, adhesion to steel exceeds the part's tear strength and ejection damages it. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.
Can mould temperature be traded against cycle time?
Only within the window stated in Table 1, and only with a recorded trial. Low temperature leaves a weak, tacky surface skin A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.
What should be recorded at incoming inspection?
Keep the measurement, the method, the sample identity and the conditions together. Trend ejection force shot by shot rather than reacting to torn parts. A result without its conditions cannot be compared with a later batch.
Does a change of LSR require re-approval?
Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For silicone rubber work the drawing alone is not enough; the process route is part of what was approved.
How many samples are enough for a first-article decision?
There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.
What belongs in the evidence pack?
The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.
Seeing this on a current silicone rubber job?
Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.
Continue reading
- Release Agent: You Cannot Buy Easy Demoulding and a Bond
- Silicone Sticking in the Mould: Cure, Release and Surface Chemistry
- Silicone Injection Moulding: Cold Runner, Hot Mould, Fast Cure
- Sticking Parts: Read the Ejection Force Trace Before Re-Polishing
- Tearing in Silicone Parts: Demoulding Force and the Undercut Nobody Drew











