PET Blister Trim Leaves Burrs That Snag the Lidding Foil

PET Blister Trim Leaves Burrs That Snag the Lidding Foil
Thin-wall forming: a production part is the only useful reference for a discussion about process drift.

PET blister flanges come off the trim press with a fine burr or string that catches the lidding foil during sealing, causing mis-seals and handling nicks.

What the failure looks like on the line

PET thin-wall packs are bought for clarity and shelf presentation, so a functional tray can still be rejected on the way it looks under cabinet lighting.

A hair-like PET burr sits on the trimmed flange edge, and lidding occasionally snags or tears as it feeds. Operators report small cuts on the glove from the edge.

PET is notch-sensitive and can stretch rather than shear cleanly when the trim knife is dull or clearance is wide. The drawn edge leaves a curl or string that stands proud of the flange and interferes with the lidding path.

Start with the failure as it is reported, not with the parameter that is easiest to measure. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. Knife clearance is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.

The process window that decides it

Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.

Переменная Typical window What fails outside it
Knife clearance 0.02-0.06 mm Wide clearance draws a burr instead of shearing
Knife sharpness interval 20k-60k strokes A dull edge strings the PET flange
Trim temperature 20-40 C Warm PET smears rather than cuts cleanly
Flange gauge 0.3-0.8 mm Thicker flanges need tighter clearance

Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.

Knife clearance is typically held at 0.02-0.06 mm. Wide clearance draws a burr instead of shearing Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.

Knife sharpness interval is typically held at 20k-60k strokes. A dull edge strings the PET flange When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.

Trim temperature is typically held at 20-40 C. Warm PET smears rather than cuts cleanly A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.

Flange gauge is typically held at 0.3-0.8 mm. Thicker flanges need tighter clearance Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.

Reading the response curve

PET Blister Trim Leaves Burrs That Snag the Lidding Foil: Clean-edge rate (%) against Strokes since regrind (k)
Figure 1. Left: Clean-edge rate (%) against Strokes since regrind (k). Right: how audited failures of this type typically split by cause. All plotted values are illustrative engineering guidance, not a measured survey.

The left panel shows clean-edge rate (%) as strokes since regrind (k) increases: the response falls from 96 to 11 on the illustrative 0–100 scale. The dashed line at 60 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.

Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.

Where the causes actually sit

The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.

Причина Illustrative share First check
Dull trim knife 35% Run a fingernail or swab along the trimmed flange to find burrs.
Wide knife clearance 25% Inspect the knife edge and record strokes since the last regrind.
Warm trim zone 18% Measure knife clearance against the flange gauge.
Thick flange 13% Check trim temperature on a long run.
High stroke count 9% Feed a lidding strip over the flange and note any snag points.

Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.

Dull trim knife accounts for roughly 35% of the illustrative split. Run a fingernail or swab along the trimmed flange to find burrs. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Wide knife clearance accounts for roughly 25% of the illustrative split. Inspect the knife edge and record strokes since the last regrind. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Warm trim zone accounts for roughly 18% of the illustrative split. Measure knife clearance against the flange gauge. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Checks before sign-off

In practice the sequence below is cheaper to run than a root-cause debate after a rejected delivery.

  1. Run a fingernail or swab along the trimmed flange to find burrs.
  2. Inspect the knife edge and record strokes since the last regrind.
  3. Measure knife clearance against the flange gauge.
  4. Check trim temperature on a long run.
  5. Feed a lidding strip over the flange and note any snag points.

Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.

Writing it into the specification and the evidence pack

Trimmed flange edges shall be free of burrs or strings beyond the agreed limit sample when inspected and swab-tested.

Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.

At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.

Evidence item What it must show
Approved drawing and revision The exact geometry and tolerances the decision applies to
Material and colour identification Grade, supplier, colour reference and any declared recycled content
Process window and change log The agreed settings and any deviation since approval
Inspection record and retained samples Method, conditions, results and a physical reference from the same lot

Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.

All ranges in this article are illustrative engineering guidance rather than measured data. Treat them as a starting agenda for a process trial, not as a certificate for a batch that has not been run.

Questions buyers ask

Is this a material problem or a process problem?

PET is notch-sensitive and can stretch rather than shear cleanly when the trim knife is dull or clearance is wide. The drawn edge leaves a curl or string that stands proud of the flange and interferes with the lidding path. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.

Can knife clearance be traded against cycle time?

Only within the window stated in Table 1, and only with a recorded trial. Wide clearance draws a burr instead of shearing A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.

What should be recorded at incoming inspection?

Keep the measurement, the method, the sample identity and the conditions together. Run a fingernail or swab along the trimmed flange to find burrs. A result without its conditions cannot be compared with a later batch.

Does a change of PET require re-approval?

Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For thin-wall forming work the drawing alone is not enough; the process route is part of what was approved.

How many samples are enough for a first-article decision?

There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.

What belongs in the evidence pack?

The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.

Seeing this on a current thin-wall forming job?

Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.

Talk to our thin-wall forming team

Последние сообщения

WhatsApp
Facebook
Twitter
LinkedIn
Pinterest
Hi there! I'm John, dad and hero to awesome kid. By day, I'm a plastics manufacturing vet — injection molding, extrusion and vacuum forming — who went from factory floors to technical management. Here to share what I've learned—let's grow together!
ru_RURU

Запросите быструю цитату

Отправьте чертежи и подробные требования по электронной почте

Emial: [email protected]

Или заполните контактную форму ниже: