
The problem
Symptom. A converter rejects a consignment of printed PET sheet because formed lids leave the line with the print 3 mm off-centre, while the supplier insists the roll met the agreed gauge and left the extruder flat.
What it costs. With no flatness limits in the sheet order, 30 000 off-register lids and a line clean-down are disputed between the supplier, who measured gauge, and the converter, who measured position.
This guide shows how to measure reel curl and edge wave on incoming rolls, link them to chain-rail misfeed, and write a flatness and registration clause into the sheet purchase order.
- 1. The misfeed is a reel-flatness fault, not a rail-setting fault
- 2. Measure curl and edge wave before adjusting the chain rails
- 3. Core set, edge-wave height and relaxation time to specify
- 4. Why flatness fails again after a storage or reel change
- 5. A reel-flatness clause for the sheet purchase order
- 6. Costing conditioned reels against a scrapped print run
The misfeed is a reel-flatness fault, not a rail-setting fault
A roll stores a curvature set by winding tension and core diameter. Unwound 0.5 mm PET can hold a 400 mm curl radius near the core and a 3 mm/m edge wave that lifts one edge clear of the pin chain.
| What the operator sees | What is physically happening | First measurement |
|---|---|---|
| Print drifts steadily off-centre | Edge wave steers the sheet across the pin chain | Edge-wave height on a 1 m strip, both edges |
| Sheet lifts at one rail | Core-set curl bows the leading edge up | Core curl radius of an unwound sample |
| Fault worst near the reel core | Tighter winding set at the inner layers | Flatness at the outer and inner reel layers |
| Good one delivery, bad the next | Reel conditioned or stored differently | Edge wave and core set measured per incoming reel |
Table 1 - Classifying a misfeed before adjusting the chain rails
Need a fixed price for this formed tray?
Send the tray drawing, sheet gauge and annual volume. We will review draft, trim and material, then quote a production tool with a written line-acceptance test.
Get a thermoforming quotationEmail [email protected]WhatsApp
Measure curl and edge wave before adjusting the chain rails
Lay a 1 m strip on a granite plate and measure edge lift and core curl with a height gauge. One audit logged 3.2 mm/m edge wave and a 380 mm core radius on the offending reel, against 0.6 mm/m and 1 200 mm on a good one.
A five-step diagnostic sequence
- Cut a 1 m strip.
Take a full-width sample from the incoming reel, before it reaches the former. - Measure both edges.
Lay it on a granite plate and record edge-wave height in mm/m with a height gauge. - Read the core set.
Measure the natural curl radius of an unwound strip from the inner layer. - Condition and repeat.
Hold the reel 24 h at 23 °C and re-measure to separate set from handling. - Correlate to the line.
Log print offset on 30 formed lids against the measured edge wave.
The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.

Core set, edge-wave height and relaxation time to specify
Three numbers protect the feed: edge wave at or below 1 mm/m, a core-set curl radius above 1 000 mm, and 24 h relaxation at 23 °C before use. A 380 mm set bows the sheet into the rails however the guides are set.
| 매개변수 | Typical target | What goes wrong outside it |
|---|---|---|
| Edge wave | ≤ 1.0 mm/m on a 1 m strip | Larger waves lift the edge off the pin chain |
| Core-set curl radius | ≥ 1 000 mm | Tight core set bows the leading edge into the rails |
| Print registration on formed lid | ≤ 0.5 mm offset | Visible drift on the retail shelf |
| Relaxation before use | 24 h at 23 °C | Fresh reels still carry winding stress |
Table 2 - Reel-flatness parameters to write on the sheet purchase order
Why flatness fails again after a storage or reel change
Flatness fails again as the reel or store changes. A warmer warehouse relaxes edge wave unevenly, a part-used reel exposes tighter core set, an over-tight unwind brake pulls the wave flat then lets it spring back, and a fresh delivery skips conditioning.
| Process variable | Effect on flatness | Practical control |
|---|---|---|
| Reel used within hours of delivery | Winding stress has not relaxed | 24 h conditioning at 23 °C before use |
| Warehouse above 30 °C | Edge wave relaxes unevenly across the width | Log storage temperature and condition on site |
| Unwind brake set too tight | Wave pulled flat then springs back in the oven | Set brake tension from a measured strip |
| Part-used reel returned to store | Inner layers carry tighter core set | Re-measure flatness after any reel change |
Table 3 - Variables that restore misfeed after sign-off
A reel-flatness clause for the sheet purchase order
A gauge certificate says nothing about shape. Add a clause: edge wave at or below 1 mm/m and a core-set curl radius above 1 000 mm on a 1 m strip, with print offset below 0.5 mm on 30 formed lids from three reels.
Want the tray checked against your line?
Send us the tray drawing and the line conditions. We will flag the geometry and material choices that cause jams, and quote a tool with an acceptance test.
What to send us
- Tray drawing with draft and radii
- Sheet grade and gauge
- Stack depth and line speed
- Drawings of the magazine or denester
Costing conditioned reels against a scrapped print run
Conditioning reels for 24 h and buying on a larger core add roughly 1-2 p per lid in handling but remove a scrapped print run. One rejected 30 000-lid consignment costs more than that allowance across the whole order.
Before you sign off this thermoformed tool
- Maximum edge-wave height and its 1 m strip measurement are stated on the sheet order
- A minimum core-set curl radius is specified, not just a gauge tolerance
- A 24 h conditioning period at a declared temperature is written into goods-in
- Print offset on formed parts is qualified across three incoming reels
- Flatness is re-measured at the inner layer of any part-used reel
A tray that looks right in the carton can still stop a filling line. Test the stack, not a single part.
Why did the roll pass a gauge check but still misfeed?
Gauge measures thickness, not shape. A reel can be spot-on 0.5 mm yet carry a 3 mm/m edge wave that steers the sheet across the pin chain. Add a flatness test to the purchase order.
Is it the chain rails or the sheet?
Measure the reel first. If edge wave exceeds 1 mm/m, tightening the rails only masks a shape fault that returns with the next reel. A good reel runs true on unchanged rails.
Why is the fault worst near the reel core?
Winding tension is highest and the curvature tightest at the core, so inner layers hold the strongest set. Measure flatness at both the outer and inner layers, not just the loose end.
Can conditioning really remove the wave?
A 24 h rest at 23 °C relaxes much of the winding stress; in one audit it cut edge wave enough to halve print offset. It cannot fully correct a tight 380 mm core set, so specify the radius on order too.
Will a tighter unwind brake hold the sheet flat?
It pulls the wave flat momentarily, then the sheet springs back as it heats in the oven. Set brake tension from a measured strip rather than using it to force a bowed reel into line.
What should the flatness clause say?
Edge wave at or below 1 mm/m and a core-set curl radius above 1 000 mm on a 1 m strip, with print offset below 0.5 mm on 30 formed lids from three reels, measured after 24 h conditioning.
Get a tray that runs on your filling line
Send us the tray drawing or a sample stack. We will review draft, trim and material, then quote a production tool with a measurable line-acceptance test written into it.
To get an accurate quote, send:
- Tray drawing or sample stack
- Sheet material and gauge
- Line speed and denesting method
- Annual volume and target unit price
Request a tool and tray quotation
Prefer to talk it through first?
이메일 [email protected] or message us on WhatsApp +86 177 1752 9949. Send a drawing, a sample or a specification and an engineer will reply.
Why buyers work with Uplastech
ISO 9001, ISO 14001 and ISO 45001 certified. Founded in 2016, with injection moulding lines in Shanghai and an extrusion plant in Jiangsu. Moulding machines from 90T to 1100T and a maximum shot weight of 5100 g. Samples and a written quotation are available on request.