
Trapped micro-bubbles and weak peel on an in-line laminated profile usually mean the nip ran outside its adhesion window.
What the failure looks like on the line
Coextruded and laminated sections fail at the interface, and the symptom is usually attributed to the visible layer rather than the bond.
An in-line laminated film shows small entrapped bubbles or a hazy patch shortly after the nip, and peel strength is uneven across the width. Adhesion may be acceptable at the line centre but poor near the edges or at start-up.
The film bonds to the warm substrate only within a narrow surface-temperature and pressure window at the nip: too cool and the melt does not wet the film, too hot and volatiles or trapped air expand into bubbles. Nip pressure and roll crown must spread contact evenly or air is folded in at the edges. A stable nip temperature and a clean, flat substrate close the window from both sides.
Start with the failure as it is reported, not with the parameter that is easiest to measure. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. Nip temperature is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.
The process window that decides it
Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.
| Variable | Typical window | What fails outside it |
|---|---|---|
| Nip temperature | 90-130 C (film dependent) | Below the window wet-out is poor; above it bubbles and distortion appear |
| Nip pressure | 1-4 bar | Low pressure leaves unwetted pockets, high pressure squeezes out the bond line |
| Substrate surface temperature | 50-80 C at nip | A cold substrate chills the interface before the film can wet it |
| Lamination line speed | 2-10 m/min | Running fast shortens contact time and traps air at the nip |
Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.
Nip temperature is typically held at 90-130 C (film dependent). Below the window wet-out is poor; above it bubbles and distortion appear Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.
Nip pressure is typically held at 1-4 bar. Low pressure leaves unwetted pockets, high pressure squeezes out the bond line When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.
Substrate surface temperature is typically held at 50-80 C at nip. A cold substrate chills the interface before the film can wet it A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.
Lamination line speed is typically held at 2-10 m/min. Running fast shortens contact time and traps air at the nip Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.
Reading the response curve

The left panel shows film adhesion (peel, relative) as nip temperature (c) increases: the response rises from 30 to 50 on the illustrative 0–100 scale. The dashed line at 60 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.
Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.
Where the causes actually sit
The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.
| Cause | Illustrative share | First check |
|---|---|---|
| Nip temperature off window | 34% | Measure substrate surface temperature immediately before the nip. |
| Uneven nip pressure | 22% | Map bubble density across the width to check roll crown and pressure evenness. |
| Cold substrate at nip | 18% | Run a short temperature ladder and peel a sample at each setting. |
| Dust or moisture on surface | 15% | Inspect the substrate for dust, moisture or die lines before the nip. |
| Line speed too high | 11% | Confirm nip pressure setting and roll condition at start-up. |
Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.
Nip temperature off window accounts for roughly 34% of the illustrative split. Measure substrate surface temperature immediately before the nip. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Uneven nip pressure accounts for roughly 22% of the illustrative split. Map bubble density across the width to check roll crown and pressure evenness. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Cold substrate at nip accounts for roughly 18% of the illustrative split. Run a short temperature ladder and peel a sample at each setting. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.
Checks before sign-off
In practice the sequence below is cheaper to run than a root-cause debate after a rejected delivery.
- Measure substrate surface temperature immediately before the nip.
- Map bubble density across the width to check roll crown and pressure evenness.
- Run a short temperature ladder and peel a sample at each setting.
- Inspect the substrate for dust, moisture or die lines before the nip.
- Confirm nip pressure setting and roll condition at start-up.
Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.
Writing it into the specification and the evidence pack
Peel strength and visible bubble count, measured by the agreed method on conditioned samples, shall stay within the stated window across the full sheet width at the production line speed.
Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.
At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.
| Evidence item | What it must show |
|---|---|
| Approved drawing and revision | The exact geometry and tolerances the decision applies to |
| Material and colour identification | Grade, supplier, colour reference and any declared recycled content |
| Process window and change log | The agreed settings and any deviation since approval |
| Inspection record and retained samples | Method, conditions, results and a physical reference from the same lot |
Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.
The values quoted here are illustrative engineering guidance, not a measured survey. Agree the test method, the sample size and the acceptance rule before comparing numbers across suppliers.
Questions buyers ask
Is this a material problem or a process problem?
The film bonds to the warm substrate only within a narrow surface-temperature and pressure window at the nip: too cool and the melt does not wet the film, too hot and volatiles or trapped air expand into bubbles. Nip pressure and roll crown must spread contact evenly or air is folded in at the edges. A stable nip temperature and a clean, flat substrate close the window from both sides. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.
Can nip temperature be traded against cycle time?
Only within the window stated in Table 1, and only with a recorded trial. Below the window wet-out is poor; above it bubbles and distortion appear A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.
What should be recorded at incoming inspection?
Keep the measurement, the method, the sample identity and the conditions together. Measure substrate surface temperature immediately before the nip. A result without its conditions cannot be compared with a later batch.
Does a change of coex require re-approval?
Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For profile extrusion work the drawing alone is not enough; the process route is part of what was approved.
How many samples are enough for a first-article decision?
There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.
What belongs in the evidence pack?
The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.
Seeing this on a current profile extrusion job?
Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.
Continue reading
- Corona Treatment of Sheet: Dyne Level, Decay and Print Adhesion
- Coextrusion Layer Adhesion: Why Layers Delaminate and How to Test
- Co-Extrusion Profiles: Dual Durometer, Tri-Extrusion and Bonding
- Protective film leaving residue after a summer in the yard: a peel dispute
- Sheet Embossing Texture: Roll Temperature, Depth and Wear











