
The problem
Symptom. Panels that measure flat at 0.30 mm at the press bow past 2 mm after the 120 C paint bake, so a passing first article turns into a rejected assembly the moment it is coated.
What it costs. The dispute lands between the moulder and the painter, both holding valid measurements, while a finished batch is scrapped and the launch slips by a requalification cycle.
This guide separates frozen-in moulding stress from oven practice, defines a post-bake flatness test, and shows which process settings to change.
Why a bake releases stored stress
A part flat at 0.30 mm can bow past 2 mm after a 120 C paint bake. The oven is not bending it; it is releasing frozen orientation and packing stress once ABS passes its glass transition near 105 C.
| Observed bow | Most likely cause | First check on the line |
|---|---|---|
| Bow grows with bake temperature | Frozen packing stress released above Tg | Measure flatness before and after a controlled bake |
| All cavities bow the same way | Process-wide residual stress | Compare hold pressure and mould temperature to the sheet |
| One corner lifts on every part | Non-uniform oven cooling or support | Log part position in the oven and cooling rate |
| Bow appears days after moulding | Post-mould shrinkage and stress relaxation | Re-measure a retained sample after 48 h |
Table 1 - Reading the bow before blaming the oven
Need a fixed price for this moulded part?
Send the 2D drawing, resin grade and annual volume. Our engineers return a DFM review, a material recommendation and a written quotation you can compare line by line.
Confirm the bow is stress release, not handling
Measure flatness before and after a controlled bake on the same five numbered parts. Deviation that grows with oven temperature on a moulding packed at 90 MPa is residual stress, not a fixture fault.
A five-step diagnostic sequence
- Measure flatness before and after a controlled bake.
Use 5 numbered parts on a granite table; a jump from 0.30 to 2 mm confirms stress release. - Record the actual oven cycle.
Log temperature and dwell; a 120 C for 45 min paint bake is above the Tg of ABS at about 105 C. - Compare hold pressure and mould temperature to the sheet.
A 90 MPa pack and a 60 C mould are the two settings that store the most stress. - Check cavity balance and oven support.
Bow that follows cavity number is filling imbalance; bow that follows oven position is cooling or fixturing. - Re-mould at lower stress and re-bake.
Drop to 55 MPa, re-measure, and only then discuss a grade change.
The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.

Specify flatness after the real process
The drawing should state service and post-process temperature, not just room-temperature flatness. Specify flatness after a defined 120 C for 45 min bake and name the grade so both parties share one condition.
| Параметр | Typical target | What goes wrong outside it |
|---|---|---|
| Hold pressure for ABS | 45-60 MPa | At 90 MPa stored stress drives post-bake bow |
| Mould temperature | 80-95 C | A cold 60 C mould freezes in orientation stress |
| Post-bake condition in the spec | 120 C for 45 min, fixtured | An undefined bake makes flatness untestable |
| Grade Tg versus bake temperature | Bake at least 20 C below Tg | Baking at or above Tg releases stress freely |
Table 2 - Stress and bake parameters for the drawing
Moulding settings that store the stress
Lowering hold pressure from 90 to 55 MPa, raising mould temperature from 60 to 90 C and balancing filling across cavities all cut the stored energy the bake later releases.
| Decision | Effect on bow | Trade-off |
|---|---|---|
| Reduce hold pressure 90 to 55 MPa | Cuts stored stress roughly in half | May reintroduce sink over bosses |
| Raise mould temperature 60 to 90 C | Slows freeze-in, lowers orientation | 3-6 s extra cooling per cycle |
| Fixture parts flat through the bake | Restrains bow during stress release | Adds a jig and a handling step |
| Switch to a higher-Tg grade | Bake sits further below Tg | Higher resin cost per kg |
Table 3 - Post-bake decisions that change flatness
Agree a post-bake acceptance test
Agree a post-bake acceptance test before first article: measure flatness on a granite table after the exact production bake, on parts from every cavity, at both ends of the moulding window.
Not sure whether the fault is in the tool or the process?
Send us the drawing, the process window and a few sample parts. We will tell you which change fixes the fault before you commit to a tool modification.
What to send us
- Part drawing with the affected dimension
- Current process settings
- Sample parts from a good and a bad batch
- Annual volume
What to do with a batch already bowed
For a batch already bowed, sorting is the short-term option. Annealing at a lower 80 C on a flat jig can recover some parts, but the permanent fix is a lower-stress process.
Before you release this injection moulding job
- Flatness is specified after the defined post-process bake, not only at room temperature
- The production bake temperature, dwell and fixturing are written into the drawing
- The grade and its Tg are named so the bake can be checked against it
- Hold pressure, mould temperature and cavity balance are recorded in the process sheet
- First-article samples are baked and measured from every cavity
Attach this list to the RFQ. Most moulding faults are decided at the drawing stage.
Why is the part flat at the press but bowed after painting?
Moulding freezes in orientation and packing stress. A paint bake near 120 C takes ABS past its Tg of about 105 C, letting that stress relax and the part move.
Can bowed parts be flattened again?
Sometimes, by re-heating on a flat jig below the distortion point, but the result is unstable. Treat it as salvage, not as a process fix.
Is a lower bake temperature enough?
Baking at 80 C instead of 120 C reduces release, but paint cure schedules are usually fixed. The robust fix is a lower-stress moulding process.
Does a higher-Tg material solve it?
It raises the margin between bake temperature and Tg, so PC at about 147 C tolerates a 120 C bake better than ABS. Requalify dimensions and cost first.
Who owns the dispute, moulder or painter?
It depends on the spec. If flatness is only defined at room temperature, the moulder passes and the painter inherits the bow. Define post-bake flatness to avoid the argument.
How many parts should we test?
At least 5 per cavity, measured before and after the exact production bake, from the lower and upper ends of the moulding window.
Get a mouldable part and a fixed quotation
Send us the part file and the failure history. Our engineers will return a DFM review, a material recommendation and a fixed quotation with a defined first-article acceptance test.
To get an accurate quote, send:
- 3D file or 2D part drawing
- Resin grade and any regrind limit
- Annual volume and target unit price
- The failed sample or defect photos
Request a DFM review and quote
Prefer to talk it through first?
Электронная почта [email protected] or message us on WhatsApp +86 177 1752 9949. Send a drawing, a sample or a specification and an engineer will reply.
Why buyers work with Uplastech
ISO 9001, ISO 14001 and ISO 45001 certified. Founded in 2016, with injection moulding lines in Shanghai and an extrusion plant in Jiangsu. Moulding machines from 90T to 1100T and a maximum shot weight of 5100 g. Samples and a written quotation are available on request.