Colour Drift in PVC Profiles: When Masterbatch Never Fully Dispersed

Colour Drift in PVC Profiles: When Masterbatch Never Fully Dispersed
Profile extrusion: a production part is the only useful reference for a discussion about process drift.

A visible shade shift or fine streaks between lengths often come from mixing energy at the extruder, not from a wrong pigment recipe.

What the failure looks like on the line

Rigid PVC profiles are produced in long runs where a small thermal drift becomes a metres-long dimensional problem before anyone sees it.

Rigid PVC profiles show a measurable shade difference between consecutive lengths, or faint colour streaks along the extrusion direction, even though the same masterbatch lot is used. Instrument readings disagree with a visual sign-off sample that was approved earlier.

Pigment agglomerates need enough shear and mixing length to break down and distribute; if back-pressure or screw mixing is low, clusters survive and the colour develops unevenly. Small changes in let-down ratio, bulk density or feed rate then shift the effective pigment concentration. Good dispersion narrows the distribution so that metre-to-metre Delta E stays small.

Buyers and suppliers usually agree on the drawing and disagree on the conditions under which the drawing was checked. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. Masterbatch let-down ratio is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.

The process window that decides it

Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.

Zmienna Typical window What fails outside it
Masterbatch let-down ratio 1-4 % w/w Outside the agreed band the shade drifts from the approved standard
Melt back-pressure 80-180 bar Too low a pressure leaves insufficient shear to break agglomerates
Melt temperature at mixing zone 170-190 C Running cool keeps the carrier viscous and dispersion poor
Colour measurement interval every 200-500 m Sparse sampling lets a drifting shade fill a full pallet

Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.

Masterbatch let-down ratio is typically held at 1-4 % w/w. Outside the agreed band the shade drifts from the approved standard Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.

Melt back-pressure is typically held at 80-180 bar. Too low a pressure leaves insufficient shear to break agglomerates When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.

Melt temperature at mixing zone is typically held at 170-190 C. Running cool keeps the carrier viscous and dispersion poor A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.

Colour measurement interval is typically held at every 200-500 m. Sparse sampling lets a drifting shade fill a full pallet Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.

Reading the response curve

Colour Drift in PVC Profiles: When Masterbatch Never Fully Dispersed: Colour deviation (relative units) against Mixing energy (relative)
Figure 1. Left: Colour deviation (relative units) against Mixing energy (relative). Right: how audited failures of this type typically split by cause. All plotted values are illustrative engineering guidance, not a measured survey.

The left panel shows colour deviation (relative units) as mixing energy (relative) increases: the response falls from 86 to 14 on the illustrative 0–100 scale. The dashed line at 35 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.

Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.

Where the causes actually sit

The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.

Przyczyna Illustrative share First check
Poor pigment dispersion 36% Measure Delta E against the retained sign-off sample under a fixed light source.
Let-down ratio drift 23% Verify the gravimetric feeder let-down ratio at the throat.
Low back-pressure 17% Raise back-pressure with a screen change and re-check streak intensity.
Masterbatch lot density change 13% Check masterbatch bulk density between lots before blaming the recipe.
Visual vs instrument dispute 11% Keep a retained sample from each shift for cross-comparison.

Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.

Poor pigment dispersion accounts for roughly 36% of the illustrative split. Measure Delta E against the retained sign-off sample under a fixed light source. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Let-down ratio drift accounts for roughly 23% of the illustrative split. Verify the gravimetric feeder let-down ratio at the throat. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Low back-pressure accounts for roughly 17% of the illustrative split. Raise back-pressure with a screen change and re-check streak intensity. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Checks before sign-off

Run the same sequence on a retained good sample and on the disputed batch so the comparison means something.

  1. Measure Delta E against the retained sign-off sample under a fixed light source.
  2. Verify the gravimetric feeder let-down ratio at the throat.
  3. Raise back-pressure with a screen change and re-check streak intensity.
  4. Check masterbatch bulk density between lots before blaming the recipe.
  5. Keep a retained sample from each shift for cross-comparison.

Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.

Writing it into the specification and the evidence pack

Colour difference against the agreed sign-off sample shall stay within the stated Delta E limit when measured under the specified illuminant and geometry, with samples retained per shift.

Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.

At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.

Evidence item What it must show
Approved drawing and revision The exact geometry and tolerances the decision applies to
Material and colour identification Grade, supplier, colour reference and any declared recycled content
Process window and change log The agreed settings and any deviation since approval
Inspection record and retained samples Method, conditions, results and a physical reference from the same lot

Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.

All ranges in this article are illustrative engineering guidance rather than measured data. Treat them as a starting agenda for a process trial, not as a certificate for a batch that has not been run.

Questions buyers ask

Is this a material problem or a process problem?

Pigment agglomerates need enough shear and mixing length to break down and distribute; if back-pressure or screw mixing is low, clusters survive and the colour develops unevenly. Small changes in let-down ratio, bulk density or feed rate then shift the effective pigment concentration. Good dispersion narrows the distribution so that metre-to-metre Delta E stays small. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.

Can masterbatch let-down ratio be traded against cycle time?

Only within the window stated in Table 1, and only with a recorded trial. Outside the agreed band the shade drifts from the approved standard A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.

What should be recorded at incoming inspection?

Keep the measurement, the method, the sample identity and the conditions together. Measure Delta E against the retained sign-off sample under a fixed light source. A result without its conditions cannot be compared with a later batch.

Does a change of PVC require re-approval?

Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For profile extrusion work the drawing alone is not enough; the process route is part of what was approved.

How many samples are enough for a first-article decision?

There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.

What belongs in the evidence pack?

The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.

Seeing this on a current profile extrusion job?

Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.

Talk to our profile extrusion team

Hi there! I'm John, dad and hero to awesome kid. By day, I'm a plastics manufacturing vet — injection molding, extrusion and vacuum forming — who went from factory floors to technical management. Here to share what I've learned—let's grow together!
pl_PLPL

Zapytaj o szybką wycenę

Prześlij rysunki i szczegółowe wymagania za pośrednictwem

Emial: [email protected]

Lub wypełnij poniższy formularz kontaktowy: