Plug-Assist Chill Marks on Housings: When the Assist Touches Too Early

Plug-Assist Chill Marks on Housings: When the Assist Touches Too Early
Thick-gauge forming: a production part is the only useful reference for a discussion about process drift.

A dull band where the plug first meets the sheet is a chill mark; tune plug temperature, timing and material before blaming the sheet.

What the failure looks like on the line

A thick-gauge enclosure is bought as a finished visible surface, so forming and trimming faults become commercial faults the moment the cover is fitted.

A matt, slightly depressed band appears across the housing where the plug first contacted the sheet, often with a faint halo at its edge.

A plug that is cooler than the sheet chills the contact patch on contact, so that region stiffens and stops stretching while the surrounding material keeps drawing. The frozen patch is carried into the part as a visible chill mark and a local thickness step.

Buyers and suppliers usually agree on the drawing and disagree on the conditions under which the drawing was checked. On a buyer's specification this distinction matters: a part can measure inside tolerance and still fail in use, because the drawing records geometry while the complaint records behaviour. Plug surface temperature is usually the first value both sides compare, and it is also the one most often quoted without the conditions attached to it.

The process window that decides it

Four variables move this result more than the rest. The ranges below are illustrative engineering guidance for a first discussion; confirm them on your own tool, material grade and part geometry before they become contract terms.

Variabel Typical window What fails outside it
Plug surface temperature Within 10-20 C of sheet temperature A cold plug freezes the contact patch immediately
Plug contact delay 0.5-2.0 s after forming temperature is reached Early contact marks a sheet that is not yet uniformly soft
Plug thermal conductivity Below 0.2 W/m K (syntactic or wood-based) A metal plug pulls heat out of the sheet too fast
Plug advance speed 50-150 mm/s, repeatable per cycle A jerky advance leaves a stepped mark at each hesitation

Table 1. Starting window for a joint process trial. Values are engineering guidance, not a measured survey.

Plug surface temperature is typically held at Within 10-20 C of sheet temperature. A cold plug freezes the contact patch immediately Record it together with the measurement point and the moment in the cycle; a single number without a location is not a process setting.

Plug contact delay is typically held at 0.5-2.0 s after forming temperature is reached. Early contact marks a sheet that is not yet uniformly soft When this drifts, the symptom usually appears at one cavity, one sheet position or one lane before it appears across the whole batch.

Plug thermal conductivity is typically held at Below 0.2 W/m K (syntactic or wood-based). A metal plug pulls heat out of the sheet too fast A change here is cheap during a trial and expensive after tooling release, so treat it as a controlled variable with a documented re-approval.

Plug advance speed is typically held at 50-150 mm/s, repeatable per cycle. A jerky advance leaves a stepped mark at each hesitation Put it on the change-control list, otherwise an unannounced material or setting substitution will be mistaken for ordinary process noise.

Reading the response curve

Plug-Assist Chill Marks on Housings: When the Assist Touches Too Early: Chill-mark severity (0-100 index) against Plug contact delay (s)
Figure 1. Left: Chill-mark severity (0-100 index) against Plug contact delay (s). Right: how audited failures of this type typically split by cause. All plotted values are illustrative engineering guidance, not a measured survey.

The left panel shows chill-mark severity (0-100 index) as plug contact delay (s) increases: the response falls from 88 to 12 on the illustrative 0–100 scale. The dashed line at 35 marks a proposed acceptance limit, not a universal standard. Move that line only after the test method and the sample plan have been agreed, otherwise two suppliers can both be compliant and still deliver different parts.

Read the shape rather than a single point. A curve that changes quickly near the limit is more sensitive to ordinary process noise than one that approaches it gradually, and that difference should be reflected in how tightly the setting is controlled and how often it is checked.

Where the causes actually sit

The right panel of Figure 1 splits audited failures of this type into five groups. The percentages are illustrative engineering guidance for prioritising an investigation, not a measured survey and not a prediction for your line.

Ursache Illustrative share First check
Plug too cold 35% Measure plug surface temperature at the start of the cycle.
Contact too early 24% Record the plug contact delay against sheet surface temperature.
Plug material too conductive 18% Inspect the plug face for damage, residue and coating wear.
Uneven sheet temperature 14% Compare the chill-mark location against the plug contact footprint.
Jerky plug advance 9% Approve a limit sample before the cycle is frozen for production.

Table 2. Cause split and the corresponding first check. Shares are indicative and sum to 100.

Plug too cold accounts for roughly 35% of the illustrative split. Measure plug surface temperature at the start of the cycle. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Contact too early accounts for roughly 24% of the illustrative split. Record the plug contact delay against sheet surface temperature. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Plug material too conductive accounts for roughly 18% of the illustrative split. Inspect the plug face for damage, residue and coating wear. Start here before authorising a material or tooling change, because it is the fastest explanation to confirm or eliminate.

Checks before sign-off

Run the same sequence on a retained good sample and on the disputed batch so the comparison means something.

  1. Measure plug surface temperature at the start of the cycle.
  2. Record the plug contact delay against sheet surface temperature.
  3. Inspect the plug face for damage, residue and coating wear.
  4. Compare the chill-mark location against the plug contact footprint.
  5. Approve a limit sample before the cycle is frozen for production.

Keep a retained reference sample beside every result. When a batch is disputed, the comparison that settles it is almost always between the retained part and the current one under the same method, not between either part and a number on a drawing. Record the instrument, the operator, the conditioning time and the position on the part or sheet for each reading.

Writing it into the specification and the evidence pack

Chill marks on the formed face shall not exceed the agreed limit sample, with plug temperature, contact delay and advance speed recorded for the approved cycle.

Write the requirement as a behaviour at a stated condition, not as a brand of material or a machine setting. State the test method, the conditioning, the sample plan and the rule for deciding a pass. Where a document is needed, ask the supplier for documentation that covers the actual construction and check its scope against your own market before approval; a document for the base material alone does not describe the finished part you are buying.

At first-article approval, freeze the drawing revision, the material and colour identification, the process window, the tool and cavity identification, and the inspection method. Any later change to grade, site, tool, or window should trigger a new first article rather than a paper waiver. Keep retained samples from the approved lot and from each production lot so that a future comparison is possible.

Evidence item What it must show
Approved drawing and revision The exact geometry and tolerances the decision applies to
Material and colour identification Grade, supplier, colour reference and any declared recycled content
Process window and change log The agreed settings and any deviation since approval
Inspection record and retained samples Method, conditions, results and a physical reference from the same lot

Table 3. Minimum evidence pack for a first-article decision and a later batch dispute.

None of the figures above should be read as a measured survey. They are engineering guidance for framing a joint trial; confirm them on your own tool, grade and geometry before they become contract terms.

Questions buyers ask

Is this a material problem or a process problem?

A plug that is cooler than the sheet chills the contact patch on contact, so that region stiffens and stops stretching while the surrounding material keeps drawing. The frozen patch is carried into the part as a visible chill mark and a local thickness step. It is worth separating the two before a supplier changes a grade: hold the material constant for one controlled run, then move one setting at a time. If the symptom follows the setting, the material was never the cause.

Can plug surface temperature be traded against cycle time?

Only within the window stated in Table 1, and only with a recorded trial. A cold plug freezes the contact patch immediately A faster cycle that sits outside the window usually moves the failure downstream, where it costs more to find.

What should be recorded at incoming inspection?

Keep the measurement, the method, the sample identity and the conditions together. Measure plug surface temperature at the start of the cycle. A result without its conditions cannot be compared with a later batch.

Does a change of enclosure housing require re-approval?

Treat any change to material grade, tool, site or process window as a change that needs a new first-article decision. For thick-gauge forming work the drawing alone is not enough; the process route is part of what was approved.

How many samples are enough for a first-article decision?

There is no universal number. Sample across cavities, lanes, sheet positions or reel lengths so that the spread is visible, not just the average. Agree the sample plan and the acceptance rule with the supplier before the trial starts.

What belongs in the evidence pack?

The approved drawing and revision, the material and colour identification, the process window, the inspection method and results, the retained reference samples, and documentation covering the actual construction. Ask the supplier to state the scope of each document and check it against your own market.

Seeing this on a current thick-gauge forming job?

Send the drawing, the material and grade, the process window you are running, and the point in the cycle or the shelf life where the fault appears. We will help you separate a material question from a process question and a specification question before anyone changes a tool.

Talk to our thick-gauge forming team

Hi there! I'm John, dad and hero to awesome kid. By day, I'm a plastics manufacturing vet — injection molding, extrusion and vacuum forming — who went from factory floors to technical management. Here to share what I've learned—let's grow together!
de_DEDE

Fordern Sie ein schnelles Angebot an

Senden Sie Zeichnungen und detaillierte Anforderungen über

Emial: [email protected]

Oder füllen Sie das untenstehende Kontaktformular aus: