{"id":9124,"date":"2024-01-03T01:00:00","date_gmt":"2024-01-03T01:00:00","guid":{"rendered":"https:\/\/uplastech.com\/lsr-metering-pump-ratio-drift-soft-hard-patches\/"},"modified":"2026-11-08T08:09:56","modified_gmt":"2026-11-08T08:09:56","slug":"lsr-metering-pump-ratio-drift-soft-hard-patches","status":"publish","type":"post","link":"https:\/\/uplastech.com\/pl\/lsr-metering-pump-ratio-drift-soft-hard-patches\/","title":{"rendered":"LSR Parts With Soft and Hard Patches: Tracing a Metering-Pump Ratio Drift"},"content":{"rendered":"<style>\n.upl-blog{font-size:17px;line-height:1.78;color:#1f2937}\n.upl-blog p{margin:0 0 18px}\n.upl-blog h2{font-size:26px;line-height:1.3;color:#0b2b33;margin:46px 0 14px;font-weight:700;letter-spacing:-.015em}\n.upl-blog h3{font-size:19.5px;color:#0d3b47;margin:28px 0 10px;font-weight:700}\n.upl-blog ul,.upl-blog ol{margin:0 0 20px;padding-left:22px}\n.upl-blog li{margin:0 0 9px}\n.upl-blog figure{margin:0 0 34px}\n.upl-blog figure img{width:100%;height:auto;display:block;border-radius:10px}\n.upl-blog figcaption{font-size:13px;color:#6b7280;margin-top:10px;line-height:1.5}\n.upl-blog .toc{background:none;border:0;border-radius:0;padding:0;margin:0 0 34px}\n.upl-blog .toc .lwptoc{margin:0}\n.upl-blog .toc h4{margin:0 0 10px;font-size:13px;letter-spacing:.1em;text-transform:uppercase;color:#0d5563}\n.upl-blog .toc ol{margin:0;padding-left:18px;font-size:14.5px}\n.upl-blog .toc li{margin-bottom:6px}\n.upl-blog table{width:100%;border-collapse:collapse;font-size:14.5px;margin:0 0 10px}\n.upl-blog th{background:#0d3b47;color:#fff;text-align:left;padding:11px 13px;font-weight:600;font-size:13.5px;border:0}\n.upl-blog td{padding:11px 13px;border:0;border-bottom:1px solid #e8ebed;vertical-align:top}\n.upl-blog tbody tr:nth-child(even){background:#fafbfc}\n.upl-blog .tablecap{font-size:12.5px;color:#6b7280;margin:0 0 30px}\n.upl-blog .myth{background:#fff8ef;border:1px solid #f6ddbd;border-radius:8px;padding:16px 20px;margin:0 0 26px;font-size:15.5px}\n.upl-blog .myth b{color:#a85c10}\n.upl-blog .callout{background:#f2f8f9;border-radius:8px;padding:18px 22px;margin:0 0 26px;font-size:15.5px;border-left:3px solid #14707f}\n.upl-blog .faq h3{border-top:1px solid #eceff1;padding-top:22px;margin-top:0;font-size:18px}\n.upl-blog .faq h3:first-of-type{border-top:0;padding-top:0}\n.upl-blog .cta{background:linear-gradient(135deg,#0b2b33,#0d5563);color:#fff;border-radius:12px;padding:34px;margin:48px 0 30px}\n.upl-blog .cta h2,.upl-blog .cta .cta-h{color:#fff;margin:0 0 10px;font-size:24px;font-weight:700;line-height:1.3}\n.upl-blog .cta p{color:#c9dee3;margin:0 0 20px;font-size:16px}\n.upl-blog .btn{display:inline-block;background:#e07a1f;color:#fff;text-decoration:none;font-weight:700;padding:13px 26px;border-radius:8px;font-size:15.5px}\n.upl-blog .rel{border-top:1px solid #e8ebed;margin-top:40px;padding-top:26px}\n.upl-blog .rel h4{font-size:13px;letter-spacing:.1em;text-transform:uppercase;color:#6b7280;margin:0 0 14px}\n.upl-blog .rel ul{list-style:none;padding:0;margin:0}\n.upl-blog .rel li{padding:11px 0;border-bottom:1px dashed #e8ebed}\n.upl-blog .rel a{text-decoration:none;font-weight:600;font-size:15.5px}\n\/* ==UPL-CONVERSION-MODULES-START== 2024 problem-solving \/ lead-gen blocks *\/\n.upl-blog .mod-h{font-size:12.5px;letter-spacing:.12em;text-transform:uppercase;font-weight:700;color:#0d5563;margin:0 0 12px}\n.upl-blog .problem{background:#fff8f3;border:1px solid #f3ddc9;border-left:4px solid #e07a1f;border-radius:10px;padding:22px 26px;margin:0 0 32px;font-size:16px}\n.upl-blog .problem p{margin:0 0 10px}\n.upl-blog .problem p:last-child{margin-bottom:0}\n.upl-blog .problem .mod-h{color:#a85c10}\n.upl-blog .problem .problem-promise{font-weight:700;color:#0b2b33}\n.upl-blog .steps{background:#f7fafb;border:1px solid #e1ebee;border-radius:10px;padding:22px 26px;margin:0 0 28px}\n.upl-blog .steps ol{list-style:none;counter-reset:uplst;margin:0;padding:0}\n.upl-blog .steps li{counter-increment:uplst;position:relative;padding:0 0 16px 42px;margin:0;font-size:15.5px}\n.upl-blog .steps li:last-child{padding-bottom:0}\n.upl-blog .steps li::before{content:counter(uplst);position:absolute;left:0;top:2px;width:26px;height:26px;border-radius:50%;background:#0d5563;color:#fff;font-size:13px;font-weight:700;line-height:26px;text-align:center}\n.upl-blog table.spec th{background:#14707f}\n.upl-blog .conv{background:#eef6f7;border:1px solid #cfe4e8;border-radius:10px;padding:24px 26px;margin:32px 0}\n.upl-blog .conv p{margin:0 0 12px;font-size:15.5px}\n.upl-blog .conv .conv-lbl{font-weight:700;color:#0b2b33;margin:16px 0 8px}\n.upl-blog ul.conv-need{list-style:none;padding:0;margin:0 0 20px;display:grid;grid-template-columns:1fr 1fr;gap:6px 18px}\n.upl-blog ul.conv-need li{position:relative;padding-left:20px;margin:0;font-size:14.5px}\n.upl-blog ul.conv-need li::before{content:\"\";position:absolute;left:0;top:9px;width:9px;height:9px;border:2px solid #14707f;border-radius:2px}\n.upl-blog .conv-btn{display:inline-block;background:#0d5563;color:#fff;text-decoration:none;font-weight:700;padding:11px 22px;border-radius:7px;font-size:15px}\n.upl-blog .checklist{background:#fbfcfd;border:1px solid #e3e9ec;border-radius:10px;padding:24px 26px;margin:36px 0}\n.upl-blog .checklist ul{list-style:none;padding:0;margin:0 0 12px}\n.upl-blog .checklist li{position:relative;padding-left:28px;margin:0 0 10px;font-size:15.5px}\n.upl-blog .checklist li::before{content:\"\";position:absolute;left:0;top:7px;width:14px;height:14px;border:2px solid #0d5563;border-radius:3px}\n.upl-blog .cl-note{font-size:13.5px;color:#6b7280;margin:0}\n.upl-blog .cta .cta-lbl{color:#c9dee3;font-weight:700;margin:0 0 8px;font-size:14.5px}\n.upl-blog ul.cta-need{list-style:none;padding:0;margin:0 0 22px;display:grid;grid-template-columns:1fr 1fr;gap:4px 18px}\n.upl-blog ul.cta-need li{color:#e4f0f2;font-size:14.5px;padding-left:18px;position:relative;margin:0}\n.upl-blog ul.cta-need li::before{content:\"\\2713\";position:absolute;left:0;color:#e07a1f;font-weight:700}\n\/* ==UPL-CONVERSION-MODULES-END== *\/\n@media(max-width:640px){.upl-blog h2{font-size:22px}.upl-blog table{font-size:13px}.upl-blog .cta{padding:24px}.upl-blog ul.conv-need,.upl-blog ul.cta-need{grid-template-columns:1fr}.upl-blog .problem,.upl-blog .steps,.upl-blog .conv,.upl-blog .checklist{padding:18px}}\n\/* \u5355\u7bc7\u9875\u9690\u85cf WhatsApp \u95ee\u5019\u5361\uff0c\u53ea\u4fdd\u7559\u5706\u5f62\u6c14\u6ce1\uff0c\u907f\u514d\u906e\u6321\u4fa7\u680f\u8be2\u76d8\u63d0\u4ea4\u6309\u94ae\u3002\n   \u6ce8\u610f\uff1aClick to Chat \u7684\u70b9\u51fb\u903b\u8f91\u662f\u300c\u95ee\u5019\u5361\u5143\u7d20\u5b58\u5728\u5c31\u4e0d\u8df3\u8f6c\u300d\uff0c\u53ea\u9760 CSS \u9690\u85cf\u4f1a\u8ba9\u6c14\u6ce1\u53d8\u6210\u6b7b\u94fe\u63a5\u3002\n   Code Snippets #9\u300cUPL single post: WhatsApp bubble jumps straight to chat\u300d\u8d1f\u8d23\u628a\u8be5\u8282\u70b9\u4ece DOM \u79fb\u9664\uff0c\n   \u4e0b\u9762\u8fd9\u6761 CSS \u53ea\u662f\u79fb\u9664\u524d\u7684\u89c6\u89c9\u515c\u5e95\u3002\u5220 #9 \u524d\u5fc5\u987b\u5148\u5220\u8fd9\u6761\u89c4\u5219\u3002 *\/\nbody.single-post .ht_ctc_chat_greetings_box{display:none !important}\n<\/style>\n<div class=\"upl-blog\">\n<figure>\n<img fetchpriority=\"high\" decoding=\"async\" src=\"https:\/\/uplastech.com\/wp-content\/uploads\/2026\/10\/fkm-seals.jpg\" alt=\"Real moulded silicone seals and O-rings made by Uplastech\" width=\"1536\" height=\"909\"><figcaption>Real silicone rubber production context. Uplastech product photo.<\/figcaption><\/figure>\n<div class=\"problem\">\n<p class=\"mod-h\">The problem<\/p>\n<p><b>Symptom.<\/b> An LSR moulding run starts producing parts with soft, tacky streaks beside hard, brittle patches, although the compound lot, mould temperature and cure time are all unchanged.<\/p>\n<p><b>What it costs.<\/b> The whole run is scrapped or sorted by hand, and because the fault looks like a bad compound the supplier is blamed while the metering pump keeps drifting into the next batch.<\/p>\n<p class=\"problem-promise\">This guide links local hardness to A:B ratio drift, gives a ten-shot weighing test and a hardness map, and sets a ratio and spread limit on the process sheet.<\/p>\n<\/div>\n<div class=\"toc\"><\/div>\n<h2 id=\"what-soft-and-hard-patches-mean-in-a-platinum-cured-lsr\">What soft and hard patches mean in a platinum-cured LSR<\/h2>\n<p>Two-part LSR is metered at 1:1, with platinum catalyst in A and Si-H crosslinker in B. A pump that slips 5 % changes crosslink density, so one area of a 40 Shore A part cures soft and tacky while another turns hard and brittle.<\/p>\n<table>\n<thead>\n<tr>\n<th>Finding on the moulded part<\/th>\n<th>Most likely cause<\/th>\n<th>Confirming check<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Soft tacky streak at the flow end<\/td>\n<td>B-side shortfall from pump lag<\/td>\n<td>Weigh A and B over ten shots<\/td>\n<\/tr>\n<tr>\n<td>Hard brittle patch near the gate<\/td>\n<td>Excess B \/ crosslinker-rich feed<\/td>\n<td>Compare the ratio log for that shift<\/td>\n<\/tr>\n<tr>\n<td>Same streak on every shot<\/td>\n<td>Blocked static mixer channelling<\/td>\n<td>Section the mixer and inspect elements<\/td>\n<\/tr>\n<tr>\n<td>Drift growing through the run<\/td>\n<td>Piston seal wear or drum warming<\/td>\n<td>Plot shot weight and drum temperature<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p class=\"tablecap\">Table 1 - Reading local soft and hard patches in LSR parts<\/p>\n<div class=\"callout\">Record which of these you are actually seeing before changing any setting. Two faults can look identical on the line and need opposite corrections.<\/div>\n<p><!-- upl-conv-v1 quickcta --><\/p>\n<div class=\"quickcta\">\n<p class=\"mod-h\">Need a fixed price for this seal?<\/p>\n<p>Send the gland drawing, temperature range, media and annual volume. We will recommend a compound with test data and return samples with a written production quotation.<\/p>\n<p class=\"quickcta-act\"><a class=\"quickcta-btn\" href=\"https:\/\/uplastech.com\/silicone-rubber\/\">Get a silicone seal quotation<\/a><a class=\"quickcta-alt\" href=\"mailto:john@uplastech.com\">Email john@uplastech.com<\/a><a class=\"quickcta-alt\" href=\"https:\/\/wa.me\/8617717529949\">WhatsApp<\/a><\/p>\n<\/div>\n<h2 id=\"weigh-the-pump-output-before-blaming-the-compound\">Weigh the pump output before blaming the compound<\/h2>\n<p>Weigh A and B separately over ten shots on a 0.1 g balance and map hardness at five points per part. The chart below plots Shore A against B-side deviation: a 10 % shortfall drops the flow end to 25 while the gate reads 30.<\/p>\n<div class=\"steps\">\n<p class=\"mod-h\">A five-step diagnostic sequence<\/p>\n<ol>\n<li><b>Freeze a reference part and the shot log.<\/b><br \/>Seal first-article mouldings and record the ratio settings before anyone adjusts the pump.<\/li>\n<li><b>Weigh A and B over ten consecutive shots.<\/b><br \/>Collect each side separately on a 0.1 g balance and compute the ratio for every shot.<\/li>\n<li><b>Map hardness at five points per part.<\/b><br \/>Measure gate, mid cavity and flow end on ten parts, 24 h after moulding, on one durometer.<\/li>\n<li><b>Inspect the static mixer and pump seals.<\/b><br \/>Section the mixer for blocked elements and check piston seal wear against the shot count.<\/li>\n<li><b>Re-set the ratio and re-map.<\/b><br \/>Balance pressures within 2 bar, fit a fresh mixer, and confirm a spread within 3 Shore A.<\/li>\n<\/ol>\n<\/div>\n<p>The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.<\/p>\n<figure>\n<img decoding=\"async\" src=\"https:\/\/uplastech.com\/wp-content\/uploads\/2026\/11\/lsr-metering-pump-ratio-drift-soft-hard-patches-chart3.jpg\" alt=\"LSR Parts With Soft and Hard Patches: Tracing a Metering-Pump Ratio Drift: calculated response trend and an illustrative root-cause split\" width=\"1536\" height=\"909\"><figcaption>Figure 1 \u2014 Calculated response trend and an illustrative root-cause split. Values are engineering guidance for diagnosis, not a measured survey; confirm them on your own line before changing a drawing or a specification.<\/figcaption><\/figure>\n<h2 id=\"set-a-ratio-and-hardness-spread-limit-on-the-process-sheet\">Set a ratio and hardness-spread limit on the process sheet<\/h2>\n<p>Write the ratio check into the process sheet: 1:1 by volume within +\/- 2 %, pump pressures balanced within 2 bar, and a 12-element static mixer. Specify 40 +\/- 5 Shore A with a 3-point maximum spread per part, measured 24 h after moulding.<\/p>\n<table class=\"spec\">\n<thead>\n<tr>\n<th>Parameter<\/th>\n<th>Typical target<\/th>\n<th>What goes wrong outside it<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>A:B metering ratio<\/td>\n<td>1:1 by volume +\/- 2 %<\/td>\n<td>A 10 % B shortfall drops hardness to 25 Shore A<\/td>\n<\/tr>\n<tr>\n<td>A\/B pump pressure balance<\/td>\n<td>Within 2 bar<\/td>\n<td>An imbalance lets one side lag each shot<\/td>\n<\/tr>\n<tr>\n<td>Hardness spread across one part<\/td>\n<td>Within 3 Shore A points<\/td>\n<td>A wider spread shows local soft and hard zones<\/td>\n<\/tr>\n<tr>\n<td>Moving-die t90 at 120 C<\/td>\n<td>90 +\/- 15 s<\/td>\n<td>Past 180 s the B-starved areas stay tacky<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p class=\"tablecap\">Table 2 - Metering and cure parameters to specify for LSR<\/p>\n<h2 id=\"separate-metering-drift-from-static-mixer-channelling\">Separate metering drift from static-mixer channelling<\/h2>\n<p>Separate pump drift from mixer channelling: a worn piston seal makes B lag on every shot, while a blocked mixer leaves a fixed streak on one side. A 10 % B shortfall also stretches t90 at 120 C from 90 s past 180 s.<\/p>\n<table>\n<thead>\n<tr>\n<th>Option<\/th>\n<th>When it fits<\/th>\n<th>Trade-off<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Re-balance A and B pump pressures<\/td>\n<td>Ratio drift under 5 %<\/td>\n<td>Needs a short line stop<\/td>\n<\/tr>\n<tr>\n<td>Fit a fresh 12-element static mixer<\/td>\n<td>A fixed streak, not a drifting one<\/td>\n<td>Consumable cost per run<\/td>\n<\/tr>\n<tr>\n<td>Replace worn piston seals<\/td>\n<td>Drift grows with shot count<\/td>\n<td>Pump service and re-qualification<\/td>\n<\/tr>\n<tr>\n<td>Condition both drums at 23 C<\/td>\n<td>Viscosity shifting A-side flow<\/td>\n<td>Drum storage and handling space<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p class=\"tablecap\">Table 3 - Corrective options for a drifting LSR metering ratio<\/p>\n<div class=\"myth\"><b>Myth:<\/b> \"A process adjustment will fix it.\" Once a design limit is reached, more tuning only adds cost and variation. Confirm the limit with a measurement, then change the drawing or the specification.<\/div>\n<h2 id=\"hold-pump-condition-and-drum-temperature-through-the-run\">Hold pump condition and drum temperature through the run<\/h2>\n<p>Hold both drums at 23 C so viscosity cannot shift A-side flow, log pump pressure each shift, and replace piston seals every 500,000 shots. Send the mapped part and shot log; we will confirm whether metering or mixing is at fault.<\/p>\n<div class=\"conv\">\n<p class=\"mod-h\">Want a compound check before you re-order?<\/p>\n<p>Send us the gland drawing and the service conditions. We will compare the compound data against your temperature range and return a recommendation with sample parts.<\/p>\n<p class=\"conv-lbl\">What to send us<\/p>\n<ul class=\"conv-need\">\n<li>Gland dimensions and cross-section<\/li>\n<li>Temperature range and media<\/li>\n<li>A failed seal if available<\/li>\n<li>Annual volume<\/li>\n<\/ul>\n<p><a class=\"conv-btn\" href=\"\/silicone-rubber\/\">Send the gland drawing<\/a>\n<\/div>\n<h2 id=\"recovery-actions-ranked-by-press-downtime\">Recovery actions ranked by press downtime<\/h2>\n<p>Recover the run by re-weighing ten shots, re-balancing pump pressures within 2 bar, and fitting a fresh mixer, then re-mapping five points on ten parts. If the spread still exceeds 3 Shore A, stop and service the pump rather than raising mould temperature.<\/p>\n<div class=\"callout\">Validate one change at a time and keep the measurement record. A supplier discussion backed by data is resolved in days, not weeks.<\/div>\n<div class=\"checklist\">\n<p class=\"mod-h\">Before you release this silicone seal<\/p>\n<ul>\n<li>A 1:1 by volume ratio within +\/- 2 % is written into the process sheet<\/li>\n<li>A and B pump pressures balanced within 2 bar are recorded each shift<\/li>\n<li>A 12-element static mixer and its change interval are specified<\/li>\n<li>Hardness is mapped at five points with a 3-point maximum spread<\/li>\n<li>Shot weight and drum temperature are logged so drift can be traced<\/li>\n<\/ul>\n<p class=\"cl-note\">Most cold or heat failures are specification gaps, not bad batches. Fix the specification before changing suppliers.<\/p>\n<\/div>\n<div class=\"faq\">\n<h3>Why are some areas soft and others hard on one part?<\/h3>\n<p>The A:B ratio sets crosslink density. Where B is short the rubber is under-cured and soft; where B is rich it is over-crosslinked and hard. A drifting pump creates both zones in the same shot.<\/p>\n<h3>Is a 2 % ratio drift acceptable?<\/h3>\n<p>Within +\/- 2 % the hardness stays inside 38-42 Shore A and the spread is under 2 points. Beyond 5 % the patches become visible and t90 at 120 C starts to climb; a 10 % shortfall pushes it past 180 s.<\/p>\n<h3>How do we tell pump drift from a blocked mixer?<\/h3>\n<p>Pump drift changes the ratio over the run and the soft zone moves; a blocked mixer leaves a fixed streak at the same place on every shot. Weigh ten shots, then section the mixer.<\/p>\n<h3>Will a hotter mould fix the tacky areas?<\/h3>\n<p>No. Extra heat may firm the bulk but cannot restore the missing crosslinker. A B-starved area stays tacky because the chemistry is short of Si-H, not short of temperature.<\/p>\n<h3>Why does the drift get worse late in a run?<\/h3>\n<p>Worn piston seals let the B side lag more with each shot, and drums warming above 23 C thin the A side. Both show up as a rising ratio error in the shot-weight log.<\/p>\n<h3>What hardness spread should we accept?<\/h3>\n<p>A maximum of 3 Shore A points across one part, measured at five points 24 h after moulding. A wider spread is the clearest sign that metering or mixing is wrong.<\/p>\n<\/div>\n<div class=\"cta\">\n<p class=\"cta-h\">Get a seal specified for the real service conditions<\/p>\n<p>Send us the gland drawing and the service conditions. We will recommend a compound with documented test data, review the squeeze, and supply samples with a production quotation.<\/p>\n<p class=\"cta-lbl\">To get an accurate quote, send:<\/p>\n<ul class=\"cta-need\">\n<li>Gland drawing or seal cross-section<\/li>\n<li>Temperature range and media<\/li>\n<li>Pressure and movement<\/li>\n<li>Annual volume and target unit price<\/li>\n<\/ul>\n<p><a class=\"btn\" href=\"\/silicone-rubber\/\">Request samples and a quotation<\/a><br \/>\n<!-- upl-conv-v1 contact --><\/p>\n<div class=\"contactbar\">\n<p class=\"contactbar-h\">Prefer to talk it through first?<\/p>\n<p>Email <a href=\"mailto:john@uplastech.com\">john@uplastech.com<\/a> or message us on <a href=\"https:\/\/wa.me\/8617717529949\">WhatsApp +86 177 1752 9949<\/a>. Send a drawing, a sample or a specification and an engineer will reply.<\/p>\n<\/div>\n<p><!-- upl-conv-v1 trust --><\/p>\n<div class=\"trust\">\n<p class=\"trust-h\">Why buyers work with Uplastech<\/p>\n<p>ISO 9001, ISO 14001 and ISO 45001 certified. Founded in 2016, with injection moulding lines in Shanghai and an extrusion plant in Jiangsu. Moulding machines from 90T to 1100T and a maximum shot weight of 5100 g. Samples and a written quotation are available on request.<\/p>\n<\/div>\n<\/div>\n<div class=\"rel\">\n<h4>Continue reading<\/h4>\n<ul>\n<li><a href=\"https:\/\/uplastech.com\/silicone-compression-set\/\">Silicone compression set<\/a><\/li>\n<li><a href=\"https:\/\/uplastech.com\/silicone-gasket-seal\/\">Silicone gasket and seal design<\/a><\/li>\n<li><a href=\"https:\/\/uplastech.com\/silicone-hardness-shore-a\/\">Silicone hardness: Shore A<\/a><\/li>\n<li><a href=\"https:\/\/uplastech.com\/silicone-industrial-seals\/\">Silicone industrial seals<\/a><\/li>\n<li><a href=\"https:\/\/uplastech.com\/silicone-o-ring-manufacturing\/\">Silicone o-ring manufacturing<\/a><\/li>\n<\/ul>\n<p><!-- upl-conv-v1 service --><\/p>\n<p class=\"rel-svc\">Ready to specify? See our <a href=\"https:\/\/uplastech.com\/silicone-rubber\/\">silicone rubber moulding services<\/a> or <a href=\"mailto:john@uplastech.com\">request a written quotation<\/a>.<\/p>\n<\/div>\n<\/div>\n<p><script type=\"application\/ld+json\">{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"Why are some areas soft and others hard on one part?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"The A:B ratio sets crosslink density. Where B is short the rubber is under-cured and soft; where B is rich it is over-crosslinked and hard. A drifting pump creates both zones in the same shot.\"}}, {\"@type\": \"Question\", \"name\": \"Is a 2 % ratio drift acceptable?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Within +\/- 2 % the hardness stays inside 38-42 Shore A and the spread is under 2 points. Beyond 5 % the patches become visible and t90 at 120 C starts to climb; a 10 % shortfall pushes it past 180 s.\"}}, {\"@type\": \"Question\", \"name\": \"How do we tell pump drift from a blocked mixer?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Pump drift changes the ratio over the run and the soft zone moves; a blocked mixer leaves a fixed streak at the same place on every shot. Weigh ten shots, then section the mixer.\"}}, {\"@type\": \"Question\", \"name\": \"Will a hotter mould fix the tacky areas?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"No. Extra heat may firm the bulk but cannot restore the missing crosslinker. A B-starved area stays tacky because the chemistry is short of Si-H, not short of temperature.\"}}, {\"@type\": \"Question\", \"name\": \"Why does the drift get worse late in a run?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Worn piston seals let the B side lag more with each shot, and drums warming above 23 C thin the A side. Both show up as a rising ratio error in the shot-weight log.\"}}, {\"@type\": \"Question\", \"name\": \"What hardness spread should we accept?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"A maximum of 3 Shore A points across one part, measured at five points 24 h after moulding. A wider spread is the clearest sign that metering or mixing is wrong.\"}}]}<\/script><\/p>\n","protected":false},"excerpt":{"rendered":"<p>This guide links local hardness to A:B ratio drift, gives a ten-shot weighing test and a hardness map, and sets a ratio and spread limit on the process sheet.<\/p>","protected":false},"author":1,"featured_media":7389,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[39],"tags":[],"class_list":["post-9124","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-silicone-rubber-products"],"meta_box":{"post-to-quiz_to":[]},"_links":{"self":[{"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/posts\/9124","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/comments?post=9124"}],"version-history":[{"count":1,"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/posts\/9124\/revisions"}],"predecessor-version":[{"id":9235,"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/posts\/9124\/revisions\/9235"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/media\/7389"}],"wp:attachment":[{"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/media?parent=9124"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/categories?post=9124"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/uplastech.com\/pl\/wp-json\/wp\/v2\/tags?post=9124"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}