Cleanliness Particulate Test Method Agreement

Real moulded silicone seals and O-rings made by Uplastech
Real silicone rubber production context. Uplastech product photo.

The problem

Symptom. A cleanliness particulate test uses different rinse and count methods between sites, so the same part returns particle counts that disagree by enough to flip the verdict.

What it costs. Reconciling the two methods forces an illustrative 9 h of re-testing and a hold while the test method is agreed.

This article quantifies the count variance by test method, sets the rinse and count rule, and writes it into the cleanliness specification.

When the particulate count depends on the method

In one illustrative case a cleanliness particulate test uses a different rinse and count method at each site, so the same part returns counts that disagree by enough to flip the accept or reject verdict.

Method trigger What it shifts First figure to check
Rinse differs Count not stable Variance vs 8 % band
Sites disagree Same part flips Illustrative 9 h retest
Filter unset Particles lost Method stated
Hold raised Stock delayed Count agreed

Table 1 - Reading a particulate method mismatch before re-testing

Record which of these you are actually seeing before changing any setting. Two faults can look identical on the line and need opposite corrections.

Need a fixed price for this seal?

Send the gland drawing, temperature range, media and annual volume. We will recommend a compound with test data and return samples with a written production quotation.

Get a silicone seal quotationEmail [email protected]WhatsApp

Quantify the count variance by test method

Quantify the variance before agreeing it. Five test methods return illustrative count variances of 4, 9, 15, 20 and 17 %; the disagreement crosses the 8 % accept band once the methods differ. These are illustrative worked values from stated assumptions, not a measured series or a quoted result.

A five-step diagnostic sequence

  1. State the rinse.
    Fix the rinse method and solvent volume before the test.
  2. Set the filter.
    Use the stated filter size so no particle is lost.
  3. Count the particles.
    Apply the stated count method to the filtered sample.
  4. Compare sites.
    Confirm both sites use the same method before release.
  5. File the method.
    Record the rinse, filter and count so the next test matches.

The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.

Cleanliness Particulate Test Method Agreement: calculated response trend and an illustrative root-cause split
Figure 1 — Calculated response trend and an illustrative root-cause split. Values are engineering guidance for diagnosis, not a measured survey; confirm them on your own line before changing a drawing or a specification.

Set the rinse and count rule

Set the rule at one stated rinse method and one stated count method. With both fixed, the variance settles at 8 % at the limit; an illustrative 9 h of re-test is the cost of the method mismatch. These are illustrative worked values from stated assumptions, not a market survey, a quoted price or a measured series.

Clause or parameter Agreed value What goes wrong outside it
Rinse method Stated per test Count not stable
Filter size Stated per test Particles lost
Count method Stated per test Verdict flips
Method owner Named per programme Method applied loosely

Table 2 - Cleanliness clauses for the specification

A controlled re-test sequence

Run the re-test in a fixed order: rinse, filter, count, then compare. The table ranks the actions by verdict risk so the method is never left to local habit.

Control action What it fixes Cost or trade-off
State rinse Comparable count Method to set
State filter No loss Filter to define
State count One number Count to agree
Re-check on change No drift after change One owner to maintain

Table 3 - Cleanliness controls ranked by verdict risk

Myth: "A process adjustment will fix it." Once a design limit is reached, more tuning only adds cost and variation. Confirm the limit with a measurement, then change the drawing or the specification.

Write the method into the cleanliness specification

Put the method in the cleanliness specification: a stated rinse, a stated filter, and a stated count. A written method turns a method dispute into one comparable count.

Want a compound check before you re-order?

Send us the gland drawing and the service conditions. We will compare the compound data against your temperature range and return a recommendation with sample parts.

What to send us

  • Gland dimensions and cross-section
  • Temperature range and media
  • A failed seal if available
  • Annual volume

Send the gland drawing

Keep the method current between changes

Re-check the method at each change, record the 9 h actually avoided, and re-forecast the test needs. A written specification reviewed on dated evidence settles the cleanliness question at test rather than at the customer.

Validate one change at a time and keep the measurement record. A supplier discussion backed by data is resolved in days, not weeks.

Before you release this silicone seal

  • The cleanliness specification states one rinse method
  • The specification states one filter size per test
  • The specification states one particle count method
  • Both sites use the same method before release
  • A named owner re-checks the method at each change

Most cold or heat failures are specification gaps, not bad batches. Fix the specification before changing suppliers.

Why agree the method?

Particle counts vary sharply with rinse and filter; different methods at different sites make the same part read differently and flip the verdict. One method keeps the count comparable.

How much does the mismatch cost?

Using illustrative assumptions reconciling the methods costs 9 h and a hold. These are worked example values, not a measured series.

What band applies?

A stated 8 % count-variance band. In this illustrative case the unaligned methods reach 20 %.

Does the filter matter?

Yes, the wrong filter size loses particles, so the count is not comparable. Stating it removes the loss.

Who owns the method?

A named programme owner re-checks it at changes. Without one owner the method drifts between sites.

Does the method expire?

It is valid until the change. Re-checking at each change keeps the cleanliness evidence current.

Get a seal specified for the real service conditions

Send us the gland drawing and the service conditions. We will recommend a compound with documented test data, review the squeeze, and supply samples with a production quotation.

To get an accurate quote, send:

  • Gland drawing or seal cross-section
  • Temperature range and media
  • Pressure and movement
  • Annual volume and target unit price

Request samples and a quotation

Prefer to talk it through first?

E-mail [email protected] or message us on WhatsApp +86 177 1752 9949. Send a drawing, a sample or a specification and an engineer will reply.

Why buyers work with Uplastech

ISO 9001, ISO 14001 and ISO 45001 certified. Founded in 2016, with injection moulding lines in Shanghai and an extrusion plant in Jiangsu. Moulding machines from 90T to 1100T and a maximum shot weight of 5100 g. Samples and a written quotation are available on request.

Hi there! I'm John, dad and hero to awesome kid. By day, I'm a plastics manufacturing vet — injection molding, extrusion and vacuum forming — who went from factory floors to technical management. Here to share what I've learned—let's grow together!
pl_PLPL

Zapytaj o szybką wycenę

Prześlij rysunki i szczegółowe wymagania za pośrednictwem

Emial: [email protected]

Lub wypełnij poniższy formularz kontaktowy: