
The problem
Symptom. A fabricator peels the protective film from a delivery of white PVC window profile after six weeks in an open yard and finds a sticky residue that no wipe will remove, and the supplier says the film was fine when it left.
What it costs. The lengths are already drilled and partly fitted, so cleaning them by hand on site costs more than the film, and the whole elevation is held while the two parties argue over a roll of tape.
This guide ties residue to storage temperature and adhesive chemistry, and gives the four checks that settle a film dispute before the profile is fitted.
Read the residue pattern before you blame the film
A pressure-sensitive adhesive is meant to stay on the film, not the profile. Below 45 °C an acrylic film peels at 0.9 N/25 mm and leaves nothing; aged for four weeks at 70 °C the same lot crosslinks, peels at 4.1 N/25 mm and leaves residue on 61% of the face.
| Storage temperature (°C) | Peel force after 4 weeks (N/25 mm) | Residue area (%) |
|---|---|---|
| 40 (covered store) | 0.9 | 0 |
| 50 | 1.4 | 3 |
| 60 | 2.6 | 24 |
| 70 (open yard) | 4.1 | 61 |
Table 1 - Storage temperature against peel force and residue area
Need a fixed price for this profile?
Send the cross-section drawing, material, cut length and annual volume. We will review die, calibration and tolerance, then return a written tooling and production quotation.
Trace the stickiness back to the yard, not the line
Typically, the cause split between open-yard heat above 45 °C, UV exposure through the wrap, film left on past twelve weeks, a rubber-resin adhesive and a dusty face at application. Check the logger first: a pallet that peaked at 70 °C left residue on 61% of the top lengths.
A five-step diagnostic sequence
- Peel a test length first.
Pull a 300 mm strip at 180° with a spring gauge; a reading over 1.5 N/25 mm and a sticky face point to storage, not the extruder. - Read the storage record.
Check the date and the yard logger; six weeks at a 70 °C peak explains 61% residue on the top layers. - Compare top and lower layers.
Peel one length from the top and one from the bottom; a large gap confirms UV and heat, not a bad film lot. - Verify the adhesive chemistry.
Confirm a UV-stable acrylic rather than a rubber-resin glue; the latter crosslinks under heat and leaves residue. - Run the storage-dwell trial.
Hold panels at 40, 50, 60 and 70 °C for four weeks and peel each; the 0.9 to 4.1 N/25 mm rise proves the yard was the cause.
The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.

Set the film and storage parameters that peel clean
Four settings keep the film releasable: a peel force below 1.5 N/25 mm after four weeks, a clean-peel yield above 90%, an acrylic rather than rubber adhesive, and removal within 12 weeks of extrusion. Above 60 °C the rubber adhesive crosslinks and residue passes 20%.
| Parametr | Typical target | What goes wrong outside it |
|---|---|---|
| Peel force after 4 weeks at 45 °C | Below 1.5 N/25 mm | Above 2.5 N/25 mm the film tears or leaves residue |
| Clean-peel yield | Above 90% of face | Below 76% the profile needs solvent cleaning on site |
| Adhesive chemistry | Acrylic, UV-stable | Rubber adhesive crosslinks under heat and UV |
| Maximum storage temperature | 45 °C | A 70 °C yard peak lifts residue to 61% of the face |
Table 2 - Film and storage settings that keep a PVC face clean
Prove it with a storage-dwell trial
Run a storage-dwell trial with one film lot: hold panels at 40, 50, 60 and 70 °C for four weeks and peel at 180°. Peel force reads 0.9, 1.4, 2.6 then 4.1 N/25 mm, while residue covers 0, 3, 24 then 61% of the face, putting the release limit near 50 °C.
| Field symptom | Most likely cause | Check that confirms it |
|---|---|---|
| Sticky film left across the whole face | Heat-aged rubber adhesive | Data logger peaked at 70 °C in the yard |
| Residue only on sun-facing lengths | UV exposure through the wrap | Top layers show 61% residue, lower layers 3% |
| Film tears into strips on pulling | Peel force above 4 N/25 mm | 180° peel gauge reads 4.1 N/25 mm |
| Clean peel at factory, residue on site | Film left on beyond 12 weeks | Extrusion date is 20 weeks before installation |
Table 3 - Matching the residue pattern to the storage fault
Write the peel test into the purchase order
Write the peel test into the order: a maximum peel force, a clean-peel yield, the adhesive chemistry and a retained film sample. When both parties peel to the same gauge and the same dwell, a sticky face becomes a 4.1 N/25 mm reading, not an argument about the roll.
Need the section checked before tooling?
Send us the section and the installation conditions. We will review wall balance, tolerance and fixing detail, then return a marked-up drawing with a tooling quotation.
What to send us
- Cross-section drawing with wall thicknesses
- Material and colour
- Installation temperature range
- Fixing method and run length
What a clean peel saves over a shipping season
A clean peel protects the elevation. A season ships 20 000 m of wrapped profile; a 45 °C limit and a twelve-week window keep 98% clean, while one uncovered pallet can fog a whole delivery before the film is pulled.
Before you release this extruded profile
- A maximum peel force of 1.5 N/25 mm after four weeks is specified
- A clean-peel yield above 90% is written into the order
- Adhesive chemistry and UV stability are stated on the film data sheet
- A 45 °C storage limit and a twelve-week removal window are agreed
- A retained film sample and a peel-test method are held by both parties
Write the measurement temperature and the tolerance into the drawing; most disputes are really about how the part was measured.
Why does my protective film leave a sticky residue?
Heat and UV aged the adhesive. A film that peels at 0.9 N/25 mm when fresh can crosslink to 4.1 N/25 mm after four weeks at 70 °C, leaving residue on 61% of the face.
Is this a bad batch of film?
Usually not. Typically, the leading cause was open-yard heat above 45 °C, followed by UV through the wrap. Compare top and lower pallet layers: residue concentrated on top points to storage, not the lot.
What peel force should I specify?
Below 1.5 N/25 mm after four weeks at 45 °C, with a clean-peel yield above 90%. Above 2.5 N/25 mm the film tends to tear or leave glue behind.
Does the adhesive type matter?
Yes. A UV-stable acrylic holds its release; a rubber-resin adhesive crosslinks under heat and sunlight. Ask for the chemistry on the data sheet, not just the colour of the film.
How long can the film stay on?
Twelve weeks from extrusion in our trials. Beyond that, even a covered pallet starts to build peel force, and a clean peel at the factory is no guarantee of one on site.
What should the acceptance clause say?
A maximum peel force, a clean-peel yield, the adhesive chemistry, a 45 °C storage limit, a twelve-week removal window and a retained sample. Then a residue dispute is settled with a peel gauge.
Get a profile that holds its dimension
Send us the profile section, the length and the service conditions. We will review die, calibration and tolerance, then quote tooling and production with a defined measurement method.
To get an accurate quote, send:
- Profile cross-section drawing
- Material and colour
- Cut length and annual volume
- Service temperature and exposure
Prefer to talk it through first?
E-mail [email protected] or message us on WhatsApp +86 177 1752 9949. Send a drawing, a sample or a specification and an engineer will reply.
Why buyers work with Uplastech
ISO 9001, ISO 14001 and ISO 45001 certified. Founded in 2016, with injection moulding lines in Shanghai and an extrusion plant in Jiangsu. Moulding machines from 90T to 1100T and a maximum shot weight of 5100 g. Samples and a written quotation are available on request.
Continue reading
- Extrusion dimensional drift
- Extrusion profile tolerance
- Profile calibration and cooling
- PVC profile weathering and colour
- PVC window profile design
Ready to specify? See our plastic profile extrusion services lub request a written quotation.