
The problem
Symptom. A buyer sends an RFQ for a 120 mm ABS housing with only a 3D file attached, so the moulder must ask for the resin, tolerances, volume and finish before any price can be built.
What it costs. Each clarification round is assumed to add 2 working days, so an incomplete pack adds an illustrative 8 days and pushes the quoted lead time out before a single part is made.
This article fixes the five files an RFQ pack needs, quantifies the round-trips each missing one adds, and writes the attachment list into the RFQ cover note.
- 1. Which five files an RFQ information pack is missing
- 2. Quantify the clarification rounds each missing file adds
- 3. Set one round-trip as the RFQ completeness target
- 4. A fixed order for assembling the RFQ pack
- 5. Write the required attachments into the RFQ cover note
- 6. Keep the RFQ pack current at each re-quote
Which five files an RFQ information pack is missing
In one illustrative request a buyer sends an RFQ for a 120 mm ABS housing with only a 3D file. The moulder cannot build a firm price without the resin grade, the toleranced 2D drawing, the annual volume, the surface finish and the acceptance standard, so the reply is a list of questions rather than a quotation.
| RFQ field | What its absence blocks | First figure to check |
|---|---|---|
| 2D drawing with tolerances | Any firm dimensional price | Clarification rounds added |
| Resin grade and maker | Shrink allowance and cycle time | Assumed shrink range |
| Annual and lifetime volume | Tooling amortisation per part | Volume band in the quote |
| Finish and acceptance standard | Cosmetic and pass or fail rule | Rework risk at first article |
Table 1 - Reading an RFQ information pack before requesting quotes
Need a fixed price for this moulded part?
Send the 2D drawing, resin grade and annual volume. Our engineers return a DFM review, a material recommendation and a written quotation you can compare line by line.
Quantify the clarification rounds each missing file adds
Count what each missing field costs. An assumed 2 working days per clarification round means a pack missing four of the five fields triggers up to 5 rounds, or 10 days, while a complete pack is quoted in 1 round, or 2 days. These are illustrative worked values from stated assumptions, not a measured series or a quoted rate.
A five-step diagnostic sequence
- List the five attachments.
Write the 2D drawing, 3D file, resin grade, volume and finish as a mandatory list on the RFQ cover. - Issue the 2D drawing first.
Send the toleranced, revision-locked 2D drawing so every supplier prices the same interpretation. - Attach the 3D file.
Include the STEP model that matches the 2D revision to avoid geometry drift between quotes. - State volume and finish.
Give annual and lifetime volume plus the cosmetic and acceptance standard in the same pack. - Record the round count.
File the issued pack and the one round-trip used so the next re-quote has dated evidence.
The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.

Set one round-trip as the RFQ completeness target
Set the completeness target at one round-trip. Reserving a single clarification round and attaching all five files cuts the illustrative 10-day quote cycle to 2 days, an 8-day saving. These are illustrative worked values from stated assumptions, not a market survey, a quoted price or a measured series. Write that one-round target and the attachment list into the RFQ cover note.
| Clause or parameter | Agreed value | What goes wrong outside it |
|---|---|---|
| Mandatory attachments | Five named files | Quote stalls in clarification |
| Clarification round target | One round-trip | Assumed 8-day slip |
| Drawing revision | Matches the 3D file | Supplier prices a stale part |
| Acceptance standard | Named in the RFQ | Pass or fail disputed later |
Table 2 - RFQ pack clauses for the cover note
A fixed order for assembling the RFQ pack
Assemble the pack in a fixed order: 2D drawing first, then 3D file, resin grade, annual volume and finally the finish and acceptance standard. The table ranks the files by the clarification rounds each one removes so the drawing is never sent last.
| Control action | What it fixes | Cost or trade-off |
|---|---|---|
| Send all five files | Removes clarification rounds | One hour of document prep |
| Lock the drawing revision | Supplier prices the right part | A revision log to maintain |
| Name the resin grade | Fixes shrink and cycle time | Grade confirmed early |
| Set one round-trip target | Caps the quote cycle at 2 days | Needs a complete first issue |
Table 3 - RFQ pack controls ranked by quote-cycle time saved
Write the required attachments into the RFQ cover note
Write the required attachments into the RFQ cover note: a controlled 2D drawing, a matching 3D file, the resin grade and maker, annual and lifetime volume, and the cosmetic and acceptance standard. A named attachment list turns a week of questions into one dated quote, so send the complete pack to [email protected] and every supplier prices on the same basis.
Not sure whether the fault is in the tool or the process?
Send us the drawing, the process window and a few sample parts. We will tell you which change fixes the fault before you commit to a tool modification.
What to send us
- Part drawing with the affected dimension
- Current process settings
- Sample parts from a good and a bad batch
- Annual volume
Keep the RFQ pack current at each re-quote
Re-issue the pack at each re-quote, record the 8 days actually saved, and re-check that the drawing revision matches the 3D file. A controlled pack reviewed on dated evidence settles completeness in one round rather than a week of email.
Before you release this injection moulding job
- The RFQ cover note lists all five mandatory attachments before any price is requested
- The 2D drawing is revision-locked and matched to the 3D file issued with it
- Resin grade, maker, annual volume and lifetime volume are stated in the RFQ
- A single clarification round-trip is set as the completeness target
- A named owner records the round count and re-issues the pack at each re-quote
Attach this list to the RFQ. Most moulding faults are decided at the drawing stage.
What should I attach to an injection moulding RFQ?
Attach a toleranced 2D drawing, a matching 3D file, the resin grade and maker, annual and lifetime volume, and the cosmetic and acceptance standard. These five files let every supplier quote on the same basis.
Why does a 3D file alone slow the quote down?
A 3D file carries geometry but not tolerances, finish or resin. Each missing field adds an assumed 2-day clarification round, so a partial pack can add an illustrative 8 days.
How do I compare quotes built on the same pack?
With the same five attachments each supplier prices the same part, so differences in tooling, unit price and lead time are real and not artefacts of different assumptions.
Who signs the RFQ pack internally?
A named buyer or sourcing owner signs it off and records the revision, so the drawing and 3D file issued to suppliers are traceable to one dated issue.
Should annual volume go in the RFQ?
Yes. Tooling amortisation depends on volume, and an omitted band lets each supplier build the unit price on a different assumed quantity.
Can I reuse the pack for a re-quote?
Re-issue it with the current drawing revision and updated volume. A controlled pack reviewed on dated evidence keeps the quote cycle at one round-trip.
Get a mouldable part and a fixed quotation
Send us the part file and the failure history. Our engineers will return a DFM review, a material recommendation and a fixed quotation with a defined first-article acceptance test.
To get an accurate quote, send:
- 3D file or 2D part drawing
- Resin grade and any regrind limit
- Annual volume and target unit price
- The failed sample or defect photos
Request a DFM review and quote
Prefer to talk it through first?
E-mail [email protected] or message us on WhatsApp +86 177 1752 9949. Send a drawing, a sample or a specification and an engineer will reply.
Why buyers work with Uplastech
ISO 9001, ISO 14001 and ISO 45001 certified. Founded in 2016, with injection moulding lines in Shanghai and an extrusion plant in Jiangsu. Moulding machines from 90T to 1100T and a maximum shot weight of 5100 g. Samples and a written quotation are available on request.











