
The problem
Symptom. A cut-length gauge drifts out of calibration and the tolerance band is shared unevenly, so cut bars come back long at one end of the run and short at the other.
What it costs. Sorting and re-cutting the out-of-band stock costs an illustrative 9 h and a hold while the gauge is calibrated and the band is allocated.
This article quantifies the length error by gauge check, sets the calibration and band, and writes the rule into the cut plan.
When cut length drifts with the gauge
In one illustrative case a cut-length gauge drifts out of calibration and the tolerance band is shared so the bar can sit at either edge, so cut lengths return errors up to 1.3 mm against a 1.0 mm tolerance.
| Gauge trigger | What it causes | First figure to check |
|---|---|---|
| Gauge drift | Length error | Error vs 1.0 mm |
| Band shared | Bar at either edge | Illustrative 9 h recut |
| Out-of-band stock | Hold raised | Calibration date |
| Customer rejects | Length disputed | Band allocated |
Table 1 - Reading a cut-length gauge drift before re-calibrating
Quantify the length error by gauge check
Quantify the error before correcting it. Five gauge checks return illustrative length errors of 0.4, 0.8, 1.3, 1.0 and 0.6 mm; the worst crosses the 1.0 mm tolerance because the band is not allocated. These are illustrative worked values from stated assumptions, not a measured series or a quoted result.
A five-step diagnostic sequence
- Calibrate the gauge.
Confirm the cut-length gauge is within calibration before any cut. - Allocate the band.
Centre the tolerance band so the bar cannot sit at either edge. - Set the cut.
Apply the calibrated gauge and the centred band to the cut length. - Verify the length.
Measure a cut bar to confirm the error is under 1.0 mm. - File the plan.
Record the calibration date and band so the next cut uses the same rule.
The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.

Set the calibration and tolerance band
Set the rule at a calibrated gauge and a centred tolerance band. With the gauge calibrated and the band allocated, the error stays under 1.0 mm; an illustrative 9 h of re-cut is the cost of the drift. These are illustrative worked values from stated assumptions, not a market survey, a quoted price or a measured series.
| Clause or parameter | Agreed value | What goes wrong outside it |
|---|---|---|
| Gauge calibration | Within date | Length error |
| Tolerance band | Centred per cut | Bar at edge |
| Re-cal interval | Stated per gauge | Drift surprise |
| Plan owner | Named per programme | Rule applied loosely |
Table 2 - Cut-length clauses for the cut plan
A controlled gauge-and-cut sequence
Run the sequence in a fixed order: calibrate, allocate the band, set the cut, then verify. The table ranks the actions by escape risk so the gauge is never the hidden variable.
| Control action | What it fixes | Cost or trade-off |
|---|---|---|
| Calibrate the gauge | Error controlled | Calibration time |
| Centre the band | No edge drift | Band to allocate |
| Re-cal on date | No surprise drift | Schedule to keep |
| Review on change | No drift after change | One owner to maintain |
Table 3 - Cut-length controls ranked by escape risk
Write the calibration rule into the cut plan
Put the rule in the cut plan: a calibrated gauge, a centred tolerance band, and a re-calibration date. A written rule turns a drifting cut into a controlled length.
Need the section checked before tooling?
Send us the section and the installation conditions. We will review wall balance, tolerance and fixing detail, then return a marked-up drawing with a tooling quotation.
What to send us
- Cross-section drawing with wall thicknesses
- Material and colour
- Installation temperature range
- Fixing method and run length
Keep the gauge current between calibrations
Re-calibrate at each interval, record the 9 h actually avoided, and re-forecast the gauge needs. A written plan reviewed on dated evidence settles the length question at cut rather than at the customer.
Before you release this extruded profile
- The cut plan uses a cut-length gauge within calibration
- The tolerance band is centred, not shared to either edge
- A re-calibration date is scheduled and kept
- Cut length is verified against the 1.0 mm tolerance
- A named owner maintains the gauge between calibrations
Write the measurement temperature and the tolerance into the drawing; most disputes are really about how the part was measured.
Why calibrate the cut gauge?
A drifting gauge pushes cut lengths to the tolerance edge, so bars come back long at one end and short at the other. Calibration keeps the error centred.
How much does the drift cost?
Using illustrative assumptions sorting and re-cutting costs 9 h and a hold. These are worked example values, not a measured series.
What tolerance applies?
A stated 1.0 mm cut-length tolerance. In this illustrative case the worst check reads 1.3 mm, over the line.
Why centre the band?
A shared band lets the bar sit at either edge; centring it removes the edge drift that causes the dispute.
Who owns the gauge?
A named programme owner re-calibrates on schedule. Without one owner the date is missed.
Does the rule expire?
It is valid until the re-calibration date. Keeping the schedule current keeps the cut evidence current.
Get a profile that holds its dimension
Send us the profile section, the length and the service conditions. We will review die, calibration and tolerance, then quote tooling and production with a defined measurement method.
To get an accurate quote, send:
- Profile cross-section drawing
- Material and colour
- Cut length and annual volume
- Service temperature and exposure










