
The problem
Symptom. A blister line rejects a lidding run because half the packs peel open at 2.1 N/15 mm in transit and the rest tear the flange at 9.2 N/15 mm, with no peel-force window in the order.
What it costs. A 300 000-pack batch is held, and the packer and the foil converter each quote their own peel test, so neither side can say whether the seal tool or the seal coat is at fault.
This guide shows how to measure peel force, set the seal temperature, dwell and pressure window, and write a peel clause into the purchase order.
- 1. A peel failure is a bond-window fault, not a seal-strength fault
- 2. Measure peel force and flange tear before raising the heat
- 3. Seal temperature, dwell and pressure to specify
- 4. Seal-coat lot variation that moves the peel force
- 5. A peel-force acceptance window for the purchase order
- 6. Costing a qualified window against a held pack batch
A peel failure is a bond-window fault, not a seal-strength fault
A peelable lid is a controlled weak bond. At 5 N/15 mm a 200 mm seal perimeter needs 5 × 200 / 15 ≈ 67 N to open; below 4 N/15 mm it opens in transit, above 6 N/15 mm the flange tears.
| What the packer sees | What is physically happening | First measurement |
|---|---|---|
| Pack opens in transit | Peel force below 4 N/15 mm, bond never formed | 180° peel force at 300 mm/min |
| Flange tears on opening | Peel force above 6 N/15 mm, bond stronger than PET | Failure mode recorded alongside force |
| Half the packs good, half bad | Seal-coat weight varies across the reel | Peel force at reel start, middle and end |
| Good one foil lot, bad the next | Lacquer chemistry changed without notice | Seal-coat certificate per incoming lot |
Table 1 - Classifying a peel fault before adjusting platen heat
Need a fixed price for this formed tray?
Send the tray drawing, sheet gauge and annual volume. We will review draft, trim and material, then quote a production tool with a written line-acceptance test.
Get a thermoforming quotationEmail [email protected]WhatsApp
Measure peel force and flange tear before raising the heat
Run a 180° peel at 300 mm/min on 30 seals and record the failure mode. A representative line reads 2.1 N/15 mm on a cold jaw at 130 °C and 9.2 N/15 mm at 170 °C, straddling the 4-6 N/15 mm window.
A five-step diagnostic sequence
- Condition the packs.
Hold 30 sealed packs at 23 °C / 50 % RH for 24 h before peeling. - Run the 180° peel.
Pull at 300 mm/min and record force in N/15 mm and the failure mode. - Map the seal-coat lot.
Test seals from the reel start, middle and end to expose coat drift. - Sweep the window.
Seal at 130, 150 and 170 °C and plot peel force against jaw temperature. - Qualify three lots.
Repeat on three lidding lots and attach the curve to first-off approval.
The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.

Seal temperature, dwell and pressure to specify
Three settings hold the window: 150 °C seal temperature, 0.8 s dwell and 0.4 MPa platen pressure. A seal-coat lot 8 % lighter shifts peel force about 1.5 N/15 mm, enough to push a 5.0 N/15 mm bond below 4.
| Paramètres | Typical target | What goes wrong outside it |
|---|---|---|
| Peel force, 180° at 300 mm/min | 4 - 6 N/15 mm | Below opens in transit, above tears the flange |
| Seal temperature | 150 °C +/- 3 °C | 130 °C under-seals, 170 °C over-seals |
| Seal dwell | 0.8 s | Short dwell leaves peel force near 2 N/15 mm |
| Platen pressure | 0.4 MPa | Low pressure leaves an unbonded strip |
Table 2 - Lidding parameters to write on the purchase order
Seal-coat lot variation that moves the peel force
The window moves again after a material change. A foil reel with 3 % different slip changes heat transfer, a platen 20 °C hotter over-seals, and a lidding lot with a different lacquer resets the whole curve per delivery.
| Process variable | Effect on peel force | Practical control |
|---|---|---|
| Seal temperature up 20 °C | Peel force rises toward flange tear | Hold 150 °C +/- 3 °C at the jaw |
| Dwell cut from 0.8 s to 0.5 s | Bond under-formed, peel force falls | Lock dwell in the press recipe |
| Platen pressure down 0.1 MPa | Low pressure leaves an unbonded strip | Hold 0.4 MPa and log per shift |
| Seal coat 8 % lighter | Peel force shifts about 1.5 N/15 mm | Require a coat-weight certificate per lot |
Table 3 - Variables that move peel force after sign-off
A peel-force acceptance window for the purchase order
A peel test with no window settles nothing. Add a clause: 4-6 N/15 mm by 180° peel at 300 mm/min on 30 seals from three lidding lots, with no flange tear above 6 N/15 mm, at steady-state platen temperature.
Want the tray checked against your line?
Send us the tray drawing and the line conditions. We will flag the geometry and material choices that cause jams, and quote a tool with an acceptance test.
What to send us
- Tray drawing with draft and radii
- Sheet grade and gauge
- Stack depth and line speed
- Drawings of the magazine or denester
Costing a qualified window against a held pack batch
Qualifying the window and buying a certified seal coat add roughly 1-2 p per pack but remove the held 300 000-pack batch. One disputed order costs more than the test work, and the clause makes later lots measurable.
Before you sign off this thermoformed tool
- A 4-6 N/15 mm peel window is stated on the purchase order, not just 'peelable'
- The 180° peel method, 300 mm/min and 23 °C / 50 % RH conditioning are written into the test
- Seal temperature, dwell and platen pressure are specified with tolerances
- A coat-weight certificate is required for every incoming lidding lot
- The acceptance test covers 30 seals from three lidding lots at steady-state platen temperature
A tray that looks right in the carton can still stop a filling line. Test the stack, not a single part.
Why do some packs open and others tear?
Peel force is a window, not a maximum. Below 4 N/15 mm the bond never formed and the pack opens; above 6 N/15 mm the bond is stronger than the PET flange and the flange tears. Both fail the same clause.
Will more heat fix an easy peel?
It raises peel force but risks flange tear and tacky foil. A jaw at 170 °C read 9.2 N/15 mm against 5.0 N/15 mm at 150 °C. Set the 150 °C, 0.8 s, 0.4 MPa window instead.
Is the fault the foil or the tool?
Measure peel force across the reel first. A drift from start to end points to seal-coat weight; a uniform shift after a jaw service points to the tool. Log both before raising the heat.
Why does peel force change with a new lidding lot?
A seal coat 8 % lighter shifts peel force about 1.5 N/15 mm, enough to move a 5.0 N/15 mm bond below the 4 N/15 mm limit. Require a coat-weight certificate and re-qualify each lot.
Can a wider seal land hide a weak bond?
It adds area but not bond strength per unit width, and it consumes printable space. Hold the 4-6 N/15 mm window and the certified seal coat rather than widening the land.
What should the peel clause say?
Peel force of 4-6 N/15 mm by 180° peel at 300 mm/min on 30 seals from three lidding lots after 24 h at 23 °C / 50 % RH, with no flange tear, at steady-state platen temperature.
Get a tray that runs on your filling line
Send us the tray drawing or a sample stack. We will review draft, trim and material, then quote a production tool with a measurable line-acceptance test written into it.
To get an accurate quote, send:
- Tray drawing or sample stack
- Sheet material and gauge
- Line speed and denesting method
- Annual volume and target unit price
Request a tool and tray quotation
Prefer to talk it through first?
Courriel [email protected] or message us on WhatsApp +86 177 1752 9949. Send a drawing, a sample or a specification and an engineer will reply.
Why buyers work with Uplastech
ISO 9001, ISO 14001 and ISO 45001 certified. Founded in 2016, with injection moulding lines in Shanghai and an extrusion plant in Jiangsu. Moulding machines from 90T to 1100T and a maximum shot weight of 5100 g. Samples and a written quotation are available on request.