
The problem
Symptom. A buyer sends out silicone seal quotations with only the word silicone rubber on the drawing, so each supplier assumes a different grade, cure system and durometer.
What it costs. Each undefined call-off field is assumed to add 3 working days and one re-quote, so an open compound description adds an illustrative 9 days before prices are comparable.
This article fixes the five compound call-off fields a buyer must lock, quantifies the re-quote loops each one removes, and writes them into the quotation request.
- 1. Which five fields a compound call-off sheet leaves open
- 2. Quantify the re-quote loops each open field adds
- 3. Set one locked grade as the quotation gate
- 4. A fixed order for locking the compound call-off
- 5. Write the call-off fields into the quotation request
- 6. Re-issue the call-off at each volume or duty change
Which five fields a compound call-off sheet leaves open
In one illustrative request a buyer asks three suppliers to quote a silicone gasket with only silicone rubber written on the drawing. One prices peroxide-cured VMQ at 60 Shore A, another platinum-cured LSR at 40 Shore A, so the three quotations are not comparable at all.
| Call-off field | What an open field blocks | First figure to check |
|---|---|---|
| Base polymer | VMQ or FVMQ selection | Assumed service temperature |
| Cure system | Post-cure and volatiles | Peroxide vs platinum flag |
| Durometer | Squeeze and sealing force | Shore A 40 to 60 band |
| Compliance standard | FDA or USP Class VI proof | Named certificate required |
Table 1 - Reading a compound call-off before requesting quotations
Need a fixed price for this seal?
Send the gland drawing, temperature range, media and annual volume. We will recommend a compound with test data and return samples with a written production quotation.
Get a silicone seal quotationEmail [email protected]WhatsApp
Quantify the re-quote loops each open field adds
Count what each open field costs. An assumed 3 working days per re-quote loop means a call-off missing four of five fields triggers up to 4 loops, or 12 days, while a locked call-off is quoted once in 3 days. These are illustrative worked values from stated assumptions, not a measured series or a quoted rate.
A five-step diagnostic sequence
- List the five call-off fields.
Write polymer, cure, durometer, colour and standard as a mandatory block on the quotation request. - Lock the base polymer.
Name VMQ or FVMQ and the maker so every supplier quotes the same family. - State the cure system.
Flag peroxide or platinum cure to fix post-cure and volatile expectations. - Fix durometer and colour.
Give Shore A value with tolerance and the colour so hardness and appearance are fixed. - Record the loop count.
File the locked call-off and the single quote used so the next volume change has dated evidence.
The chart below is a typical result from that measurement step. Use it to separate a design limit from a setting that can still be recovered.

Set one locked grade as the quotation gate
Set one locked grade as the quotation gate. Stating all five call-off fields cuts the illustrative 12-day quote cycle to 3 days, a 9-day saving. These are illustrative worked values from stated assumptions, not a market survey, a quoted price or a measured series. Write that locked call-off into the quotation request.
| Clause or parameter | Agreed value | What goes wrong outside it |
|---|---|---|
| Mandatory call-off fields | Five named entries | Prices are not comparable |
| Grade lock | One locked polymer | Assumed 9-day re-quote slip |
| Durometer tolerance | Stated in Shore A | Suppliers quote different hardness |
| Compliance standard | Named in the request | Certificates disputed later |
Table 2 - Compound call-off clauses for the quotation request
A fixed order for locking the compound call-off
Assemble the call-off in a fixed order: base polymer first, then cure system, durometer, colour and finally the compliance standard. The table ranks the fields by the re-quote loops each one removes so the polymer is never left open.
| Control action | What it fixes | Cost or trade-off |
|---|---|---|
| Lock all five fields | Removes re-quote loops | One hour of spec prep |
| Name the cure system | Fixes post-cure and volatiles | Cure confirmed early |
| State Shore A tolerance | Supplier quotes the right hardness | A durometer check to keep |
| Set one quotation gate | Caps the cycle at 3 days | Needs a locked first issue |
Table 3 - Call-off controls ranked by quote-cycle time saved
Write the call-off fields into the quotation request
Write the call-off into the quotation request: base polymer and maker, peroxide or platinum cure, Shore A durometer and tolerance, colour, and the named FDA or USP Class VI standard. A locked call-off lets every supplier quote the same material, so send it to [email protected] with the drawing.
Want a compound check before you re-order?
Send us the gland drawing and the service conditions. We will compare the compound data against your temperature range and return a recommendation with sample parts.
What to send us
- Gland dimensions and cross-section
- Temperature range and media
- A failed seal if available
- Annual volume
Re-issue the call-off at each volume or duty change
Re-issue the call-off at each volume or duty change, record the 9 days actually saved, and re-check that the stated durometer matches the service duty. A controlled call-off reviewed on dated evidence settles the grade in one quote rather than four loops.
Before you release this silicone seal
- The quotation request lists all five compound call-off fields before any price is requested
- The base polymer and maker are named and matched to the service duty
- Cure system, Shore A durometer with tolerance and colour are stated in the request
- The compliance standard is named with the certificate the supplier must return
- A named owner records the re-quote loops and re-issues the call-off at each change
Most cold or heat failures are specification gaps, not bad batches. Fix the specification before changing suppliers.
What should a compound call-off sheet state?
State the base polymer and maker, the cure system, the Shore A durometer and tolerance, the colour and the named compliance standard. These five fields make every quotation comparable.
Why does saying only silicone rubber cause re-quotes?
The word covers many grades and hardnesses. Each open field adds an assumed 3-day re-quote loop, so a vague call-off can add an illustrative 9 days.
How do I compare quotations built on the same call-off?
With the same five fields each supplier prices the same material, so differences in unit price, tooling and lead time are real and not different assumptions.
Who signs the compound call-off internally?
A named buyer or sourcing owner signs it off and records the revision, so the grade issued to suppliers is traceable to one dated decision.
Should the compliance standard go in the request?
Yes. Naming FDA or USP Class VI up front fixes the certificate burden, and an omitted standard lets each supplier price a different test package.
Can I reuse the call-off at a volume change?
Re-issue it with the current durometer and duty. A locked call-off reviewed on dated evidence keeps the quote cycle at one round.
Get a seal specified for the real service conditions
Send us the gland drawing and the service conditions. We will recommend a compound with documented test data, review the squeeze, and supply samples with a production quotation.
To get an accurate quote, send:
- Gland drawing or seal cross-section
- Temperature range and media
- Pressure and movement
- Annual volume and target unit price
Request samples and a quotation
Prefer to talk it through first?
Correo electrónico [email protected] or message us on WhatsApp +86 177 1752 9949. Send a drawing, a sample or a specification and an engineer will reply.
Why buyers work with Uplastech
ISO 9001, ISO 14001 and ISO 45001 certified. Founded in 2016, with injection moulding lines in Shanghai and an extrusion plant in Jiangsu. Moulding machines from 90T to 1100T and a maximum shot weight of 5100 g. Samples and a written quotation are available on request.
Continue reading
- Silicone compression set
- Silicone gasket and seal design
- Silicone hardness: Shore A
- Silicone industrial seals
- Silicone o-ring manufacturing
Ready to specify? See our silicone rubber moulding services o request a written quotation.









